DS200PCCAG8ACB工控模块
断开电源
重新夹紧或连接夹具前，断开电源。开始安装前，请仔细阅读所有说明。注意安全 为避免火灾或电击风险，必须按照所有适用的国家和地方电气/建筑规范安装固定装置。 本装置的安装和维护需要一名电工或经过工厂认证的技术人员。 如果要更换现有夹具，请将其拆下，并记下夹具连接到插座盒中的哪根导线上。不要分开盒子里的任何其他电线。不要损坏旧电线的绝缘层。在正常情况下，黑色导线为“热”导线，白色导线为“中性”或“普通”导线。绿色或裸铜线为“地线”。在较旧的建筑物中，重新确认接线的极性总是一种好做法。通知 本表中概述的重要安全措施和说明不能涵盖可能发生的所有情况和情况。必须理解的是，常识、谨慎和小心是任何产品都不可能具备的因素。安装、操作和维护此照明设备的人员必须小心。 该夹具设计用于安装在正确安装的标准圆形或八角形盒或带有石膏框架的直通出线盒上。箱子必须牢固地安装在建筑物的结构上。应使用提供的安装杆和五金件。将夹具直接安装到出线盒可能导致无法正确对齐夹具。 注意：为了您的安全，请确保控制室外照明和设备的断路器是GFI断路器。
夹具准备
1.从纸箱中取出夹具、零件和零件袋。注意：在丢弃纸箱之前，请仔细检查以确保找到所有零件。夹具安装1.确定夹具的总长度。将导线和接地线从阀杆、球接头引导至顶棚中心。测量超出夹具中心6“的导线和地线。切断多余的电线。剥去导线端部的绝缘层，露出约1/2“的导线。把几股电线拧在一起。2.将2个最长的螺钉拧入安装板，并将六角螺母拧到螺钉上（绿色接地螺钉位于前面）。将安装板连接到出线盒。（绿色螺钉应面向地板）。3.将小六角螺母拧到螺钉上。调整螺钉，使其伸出夹具背面3/16“，将六角螺母锁紧在横杆上。4.将接地线固定在出线盒中的绿色或裸铜线或横杆上的绿色螺钉上。警告：切勿将接地线紧固在黑色或“热”线上！不遵守此说明可能导致重伤或死亡！2018年2月1日24日5日。将白色夹具引线固定到出线盒中的白色导线上。用认可的紧固件（导线螺母）将导线固定在一起。从紧固件下方约1“处开始，用胶带紧紧包裹连接件，使连接件密封紧固件的端部。警告：确保没有可能导致危险短路的裸露电线或线束！6.将黑色夹具引线连接至出线盒中的黑色导线。按照步骤5..7紧固连接的导线。将玻璃放入插座，并用插座环锁定。8.安装灯（灯泡）。注：此灯具的额定功率为最大60瓦A型或早期电灯。警告不要超过建议的瓦数！9.恢复断路器或保险丝盒处电路的电源。
Disconnect power
Disconnect the power supply before re clamping or connecting the fixture. Please read all instructions carefully before starting the installation. Attention to safety To avoid the risk of fire or electric shock, fixtures must be installed in accordance with all applicable national and local electrical/building codes. An electrician or factory certified technician is required for the installation and maintenance of this device. If the existing clamp is to be replaced, remove it and note which wire the clamp is connected to in the socket box. Do not separate any other wires in the box. Do not damage the insulation of old wires. Under normal conditions, black conductors are "hot" conductors and white conductors are "neutral" or "normal" conductors. Green or bare copper wire is "ground wire". In older buildings, it is always a good practice to reconfirm the polarity of the wiring. Notice The important safety measures and instructions outlined in this table cannot cover all possible situations and circumstances. It must be understood that common sense, caution and caution are factors that no product can possess. The personnel who install, operate and maintain this lighting must be careful. The fixture is designed to be installed on a properly installed standard circular or octagonal box or straight outlet box with gypsum frame. The box must be firmly mounted on the structure of the building. Mounting rods and hardware provided shall be used. Mounting the clamps directly to the outlet box may result in incorrect alignment of the clamps. Note: For your safety, please ensure that the circuit breaker controlling outdoor lighting and equipment is GFI circuit breaker.
Fixture preparation
1. Take out the clamp, parts and parts bag from the carton. Note: Before discarding the carton, please carefully check to ensure that all parts are found. Fixture installation 1. Determine the total length of the fixture. Guide the conductor and ground wire from the valve stem and ball joint to the center of the ceiling. Measure the wire and ground wire 6 "beyond the center of the clamp. Cut off the excess wire. Strip the insulation layer at the end of the wire to expose about 1/2" of the wire. Screw several strands of wire together. 2. Screw the two longest screws into the mounting plate, and screw the hex nut onto the screw (the green grounding screw is at the front). Connect the mounting plate to the outlet box. (The green screw should face the floor) 。 3. Screw the small hexagon nut onto the screw. Adjust the screw so that it extends 3/16 "beyond the back of the clamp, and lock the hex nut on the cross bar. 4. Fix the grounding wire on the green or bare copper wire in the outlet box or the green screw on the cross bar. Warning: Do not fasten the grounding wire on the black or" hot "wire! Failure to follow this instruction may result in serious injury or death! February 1, 2018, 24, 5. Secure the white clamp leads to the white wires in the outlet box. Secure the wires together with approved fasteners (wire nuts). Starting from about 1 "below the fastener, wrap the connector tightly with adhesive tape so that the connector seals the end of the fastener. Warning: Make sure there are no exposed wires or harnesses that may cause a dangerous short circuit! 6. Connect the black clamp lead to the black wire in the outlet box. Tighten the connected wire according to step 5.. 7. Put the glass into the socket and lock it with the socket ring. 8. Install the lamp (bulb) 。 Note: The rated power of this lamp is 60 watt type A or early electric lamp at most. Warning Do not exceed the recommended wattage! 9. Restore the power supply of the circuit at the circuit breaker or fuse box.
