3BSE003643R1 PM152工控DCS系统备件
参考操作条件环境温度：
23°C±2°C环境湿度：55%RH±5%（无冷凝）电源电压：一般电源规格100VAC±1%24V电源规格24VDC±1%电源频率：一般电源规范50/60Hz±0.5%24V电源规范直流安装角度：向前或向后±3°，横向±3°安装高度：海拔2000m或以下振动：0m/s2振动：0m/s 2安装条件：单单元面板安装（需要单元上方、下方、右侧和左侧的空间。)风：无外部噪音：无预热时间：30分钟或更长正常运行条件环境温度：-10°C至50°C（封闭安装时为-10°C到40°C）环境湿度：10至90%RH（无冷凝）电源电压：一般电源规格90至264VAC 24V电源规格21.6至26.4VDC/AC电源频率：一般电源规格50/60Hz±2%24V电源规格DC，50/60赫兹±2%安装角度：向前或向后±10°，横向±10°安装高度：海拔2000m或以下振动：2m/s2震动：0m/s2安装条件：单单元面板安装（需要单元上下空间）。)
外部噪音：
无环境温度变化率：10°C/小时或更低运输条件环境温度：-20°C至60°C环境湿度：5至90%RH（无冷凝）振动：4.9m/s2（10至60Hz）冲击：392m/s2在装置包装好以供工厂装运的条件下储存条件环境温度为-20°C到60°C长期储存，温度应为10°C至30°C。环境湿度：5至90%RH（无冷凝）振动：0m/s2振动：0m/s 2在设备由工厂包装装运的条件下显示规格上显示屏：LED下显示屏：LCD（带背光）108 x 24点4选项z通信接口带RS232C、RS422A或RS485，控制器的设置和测量值可以被传送到主CPU，并且各种参数可以由主CPU设置。通信点数量：1点通信类型：RS232C、RS422A、RS485通信速度：2400/4800/9600/19200/38400 bps协议：MODBUS（RTU）、MODBUS（ASCII）、PRIVATE z数字信号输入通过数字输入信号启用以下切换。输入信号：无电压触点，
Reference operating conditions Ambient temperature:
23 ° C ± 2 ° C Ambient humidity: 55% RH ± 5% (non condensing) Power supply voltage: general power supply specification 100VAC ± 1% 24V power supply specification 24VDC ± 1% Power frequency: general power supply specification 50/60Hz ± 0.5% 24V power supply specification DC installation angle: forward or backward ± 3 °, transverse ± 3 ° Installation height: altitude 2000m or below Vibration: 0m/s2 Vibration: 0m/s2 Installation condition: single unit panel installation (space above, below, right and left of the unit is required) Wind: no external noise: no warm-up time: 30 minutes or more; normal operating conditions; ambient temperature: - 10 ° C to 50 ° C (- 10 ° C to 40 ° C when closed installation); ambient humidity: 10 to 90% RH (non condensing); power supply voltage: general power supply specification: 90 to 264VAC; 24V; power supply specification: 21.6 to 26.4VDC/AC; power frequency: general power supply specification: 50/60Hz ± 2%; 24V; power supply specification: DC; 50/60Hz ± 2%; installation angle: forward or backward ± 10 °, Transverse ± 10 ° installation height: 2000m above sea level or below Vibration: 2m/s2 Vibration: 0m/s2 Installation condition: single unit panel installation (requires space above and below the unit)
External noise:
No ambient temperature change rate: 10 ° C/hour or lower; transportation conditions; ambient temperature: - 20 ° C to 60 ° C; ambient humidity: 5 to 90% RH (non condensing); vibration: 4.9m/s2 (10 to 60Hz); impact: 392m/s2; storage conditions; ambient temperature: - 20 ° C to 60 ° C; long-term storage; temperature: 10 ° C to 30 ° C. Ambient humidity: 5 to 90% RH (non condensing) Vibration: 0 m/s2 Vibration: 0 m/s2 Display specifications when the equipment is packed and shipped in the factory Upper display screen: LED Lower display screen: LCD (with backlight) 108 x 24 point 4 option z Communication interface with RS232C, RS422A or RS485, the settings and measured values of the controller can be transmitted to the main CPU, and various parameters can be set by the main CPU. Number of communication points: 1 point Communication type: RS232C, RS422A, RS485 Communication speed: 2400/4800/9600/19200/38400 bps Protocol: MODBUS (RTU), MODBUS (ASCII), PRIVATE z Digital signal input enables the following switching through the digital input signal. Input signal: no voltage contact,
