3BSE003127R1 57120001-P工控DCS系统备件
3输出规格输出信号：
模拟输出4至20mA，0至1V，0至10V数字输出RS422A，RS485精度等级：满量程的±0.1%输出更新周期：模拟输出约0.1秒数字输出约1秒分辨率：约1/30000输出阻抗：电压输出约10Ω 负载电阻：电流输出400Ω 或更低电压输出50kΩ 或更少通用规范编程模式数：30模式模式重复…最大9999倍编程步骤数：19步/模式步重复…最大99倍额定电源电压：通用电源规格100至240VAC 24V电源规格24VAC/24VDC额定电源频率：通用电源规范50/60Hz 24V电源规范50/60Hz（24VAC）最大功耗：一般电源规格无选件100VAC 10VA 240VAC 15VA有选件100V 15VA 240V 20VA 24V电源规格无选件24V 10VA 24VDC 5W有选件24V 15VA 24VDC 10W电源故障对策：设置存储在EEPROM中（重写次数：100万次或更少），由锂电池存储5年或以上端子螺钉：M3.5绝缘电阻：一次端子和二次端子之间20MΩ 一次端子和接地端子20M之间的电压大于或等于（500VDC）Ω 二次端子和接地端子20M之间的电压大于或等于（500VDC）Ω 或以上（500VDC）
耐受电压：
一次端子和二次端子之间1500VAC（持续1分钟）一次端子与接地端子之间150VAC（1分钟）二次端子和接地端子500VAC（保持1分钟）*一次端子：电源端子（100至240VAC），控制输出和报警输出外壳：阻燃聚碳酸酯颜色：灰色或黑色安装：面板安装外部尺寸：96（高）x 96（宽）x 127（深）mm*距前面板的深度为120mm。重量：无选件约450克有选件约580克SAFTY STANDARD CE指令：EN61326:1997+A1+A2+A3 EN61010-1:2001（过电压类别II，污染程度2）*在EMC指令的测试条件下，指示值或输出值的变化可能相当于最大±10%或最大2mV，以较大者为准。UL:UL61010-1第2版c–UL:CAN/CSA C22.2第61010-1-04号
3 Output specification Output signal:
Analog output 4 to 20mA, 0 to 1V, 0 to 10V digital output RS422A, RS485 accuracy class: ± 0.1% of full scale Output update cycle: about 0.1 seconds for analog output Digital output about 1 second Resolution: about 1/30000 Output impedance: about 10 Ω for voltage output Load resistance: 400 Ω for current output or lower Voltage output 50k Ω or less Number of programming modes in general specification: 30 Mode repeat... 9999 times the maximum number of programming steps: 19 steps/Mode repeat... 99 times the maximum rated power supply voltage: 100 to 240VAC in general power specification 24V power specification 24VAC/24VDC Rated power frequency: general power specification 50/60Hz 24V power specification 50/60Hz (24VAC) Maximum power consumption: general power specification No option 100VAC 10VA 240VAC 15VA option 100V 15VA 240V 20VA 24V power specification No option 24V 10VA 24VDC 5W option 24V 15VA 24VDC 10W power failure countermeasure: set and store in EEPROM (rewrite times: 1 million or less), Terminal screw stored by lithium battery for 5 years or more: M3.5 Insulation resistance: 20M Ω between primary terminal and secondary terminal The voltage between primary terminal and ground terminal 20M is greater than or equal to (500VDC) Ω The voltage between secondary terminal and ground terminal 20M is greater than or equal to (500VDC) Ω or more (500VDC)
Withstand voltage:
1500VAC (lasting for 1 minute) between primary terminal and secondary terminal 150VAC (lasting for 1 minute) between primary terminal and grounding terminal 500VAC (lasting for 1 minute) * primary terminal: power terminal (100 to 240VAC), Control output and alarm output housing: flame-retardant polycarbonate color: gray or black Installation: panel installation External dimension: 96 (H) x 96 (W) x 127 (D) mm * The depth from the front panel is 120mm. Weight: about 450g without options; about 580g with options; SAFTY STANDARD CE Directive: EN61326:1997+A1+A2+A3 EN61010-1:2001 (overvoltage category II, pollution degree 2) * Under the test conditions of EMC Directive, the change of indicated value or output value may be equivalent to the maximum ± 10% or the maximum 2mV, whichever is greater. UL: UL61010-1 Version 2 c – UL: CAN/CSA C22.2 No. 61010-1-04
