AO845A-eA使用方法
弹出“打印机端口”窗口
选择“标准TCP/IP端口”，单击“新建端口”。5） 弹出“添加标准TCP/IP打印机端口向导”窗口，单击“下一步”。6） 弹出“添加端口”窗口，导入“打印机名称或IP地址”列中“设置打印机的IP地址”报告的IP地址。以IP地址“192.168.0.240”为例。“端口名”在填写完IP地址后自动创建。单击“下一步”。TP830用户手册-29-7）弹出“需要附加端口信息”窗口，在“设备类型”中选择“自定义”，然后单击“设置”。8） 弹出“端口设置”窗口。确认“端口名”和“打印机名或IP地址”正确，“协议”为“RAW”，“端口号”为“9100”，单击“确定”。TP830用户手册-30-9）返回“所需附加端口信息”，单击“下一步”。10） 弹出“完成添加标准TCP/IP打印机端口向导”窗口，单击“完成”。11） 返回“打印机端口”，单击“关闭”。12） 返回“属性”，确保选择了网络端口，单击“应用”，然后单击“关闭”。这样，打印机的网络端口设置完成。
用户手册
使用手册-32-第3章控制面板3.1控制面板控制面板上有三个LED和一个按键。（如图3-1所示）3.1.1 LED LED说明POWER（绿色）表示打印机电源是否已连接。电源接通时，LED亮起。错误（红色）表示打印机的状态。出现故障时，LED亮起。出纸（红色）表示打印机的纸张状态。当纸张用完或即将结束时，LED亮起。3.1.2功能键说明【FEED】【FEED」控制进纸，您可以通过命令启用或禁用键功能。启用后，如果按住不放，纸张将连续进纸，如果松开，纸张将停止进纸。3.2自检自检打印让您知道打印机是否正常工作。如果打印机正常打印自检内容，则表示除了连接到计算机的接口之外，打印机没有任何问题。否则，应修复打印机。打印机将打印出自检信息，如软件版本和界面等。按住FEED键并在打印机盖关闭时打开电源开关，ERROR LED闪烁一次并发出两声蜂鸣声（如果打印机中安装了蜂鸣器）。松开键，然后打印机打印出自检信息。
The Printer Port window pops up
Select Standard TCP/IP Port and click New Port. 5) The Add Standard TCP/IP Printer Port Wizard window pops up, and click Next. 6) Pop up the "Add Port" window, and import the IP address of the "Set the IP Address of the Printer" report in the "Printer Name or IP Address" column. Take the IP address "192.168.0.240" as an example. The Port Name is automatically created after the IP address is filled in. Click Next. TP830 User Manual-29-7) The "Additional Port Information Required" window pops up, select "Custom" in "Device Type", and then click "Settings". 8) The Port Settings window pops up. Confirm that the Port Name and Printer Name or IP Address are correct, the Protocol is RAW, and the Port Number is 9100. Click OK. TP830 User Manual - 30-9) Return to "Additional Port Information Required" and click "Next". 10) The window "Completing the Add Standard TCP/IP Printer Port Wizard" pops up, and click "Finish". 11) Return to Printer Port and click Close. 12) Return to Properties, make sure the network port is selected, click Apply, and then click Close. In this way, the printer's network port is set.
user 's manual
Operating Manual-32 - Chapter 3 Control Panel 3.1 Control Panel There are three LEDs and a key on the control panel. (As shown in Fig. 3-1) 3.1.1 LED indicates that POWER (green) indicates whether the printer power is connected. The LED lights up when the power is turned on. Error (red) indicates the status of the printer. The LED lights up when a fault occurs. Paper out (red) indicates the paper status of the printer. The LED lights when the paper is used up or about to end. 3.1.2 Function key description [FEED] [FEED "controls the paper feeding. You can enable or disable the key function through the command. After enabling, if you press and hold it, the paper will feed continuously. If you release it, the paper will stop feeding. 3.2 Self inspection and self inspection printing let you know whether the printer works normally. If the printer prints the self inspection content normally, it means that the printer has no problem except the interface connected to the computer. Otherwise, the printer should be repaired. The printer will Print the self inspection information, such as software version and interface. Press and hold the FEED key and turn on the power switch when the printer cover is closed. The ERROR LED flashes once and emits two beeps (if a buzzer is installed in the printer). Release the key, and then the printer prints the self-test information.
