A5E36717788处理器模块
图片文件
由MS Office产品使用。例如，您可以通过Word的菜单命令“插入-图片-来自文件”将保存的图片文件插入Word文档。使用此命令，您可以将屏幕上的程序页面（逆时针旋转90度）保存为图片（增强型图元文件）格式的磁盘文件。此文件的文件扩展名必须为EMF。图片文件由MS Office产品使用。例如，您可以通过Word的菜单命令“插入-图片-来自文件”将保存的图片文件插入Word文档。标准用户界面：使用此命令，您可以在屏幕上打印程序。高级用户界面：使用此命令可以打印程序页面。您可以打印所有页面或所需页面（或页面范围）。第一页（即最左边的页面选项卡）的页码为1。选择“打印”命令后，当前可见页面的页码将显示在“打印”对话框中。此命令停止执行DriveAP。
电脑硬件
如果有一个驱动器连接到您的电脑硬件，您可以通过此命令将软件连接到该驱动器。如果有多个驱动器连接到电脑硬件，您可以从可用驱动器列表中选择该驱动器。连接的驱动器的标识符显示在屏幕顶部。此命令将DriveAP的操作模式更改为离线模式（参见第3章-DriveAP使用中的离线模式一节）。如果您想使用另一个连接到电脑的驱动器，请通过此命令断开当前连接的驱动器，然后通过命令drive-Connect连接到另一个驱动器。此命令将DriveAP的操作模式更改为独立模式。此命令上载并显示所连接驱动器的AP程序。将垂直图片另存为…打印…退出驱动器菜单连接断开上传菜单命令DriveAP用户手册4-3注意（仅限标准用户界面）：当DriveAP上传连接到参数且其位号为0的输入引脚的连接信息时，DriveAP不知道该输入引脚是否连接到该参数的位0或整个参数值。在这种情况下，DriveAP假设它连接到整个值，并删除位号0。如果用户知道它实际上连接到位0，他可以单击此输入引脚（同时按住Ctrl键），并将位号0写入屏幕上显示的对话框的位号字段，然后单击确定按钮。现在，位号0显示在框图中。如果需要，现在可以修改屏幕上的AP程序（参见第3章“DriveAP的使用”中的“程序修改”一节）。该命令将屏幕上的程序下载到连接的驱动器。如果需要，DriveAP会在下载后启动驱动器中的下载程序。该命令将DriveAP的操作模式更改为联机模式（参见第3章-DriveAP使用中的联机模式一节）。
Picture file
Used by MS Office products. For example, you can insert a saved picture file into a Word document through the Word menu command "Insert - Picture - From File". With this command, you can save the program page on the screen (rotated 90 degrees counterclockwise) as a disk file in the format of a picture (enhanced metafile). The file extension for this file must be EMF. Picture files are used by MS Office products. For example, you can insert a saved picture file into a Word document through the Word menu command "Insert - Picture - From File". Standard user interface: With this command, you can print the program on the screen. Advanced user interface: Use this command to print program pages. You can print all pages or the desired pages (or page ranges). The first page (the leftmost page tab) has a page number of 1. When you select the Print command, the page number of the currently visible page is displayed in the Print dialog box. This command stops DriveAP execution.
Computer hardware
If a drive is connected to your computer hardware, you can use this command to connect the software to the drive. If you have more than one drive connected to your computer hardware, you can select it from the list of available drives. The identifier of the connected drive is displayed at the top of the screen. This command changes the operation mode of DriveAP to offline mode (see Chapter 3 - Offline Mode in DriveAP Use). If you want to use another drive connected to the computer, use this command to disconnect the currently connected drive, and then use the command drive Connect to Connect to another drive. This command changes the operation mode of DriveAP to standalone mode. This command uploads and displays the AP program for the connected drive. Save the vertical picture as... Print... Exit the drive menu Connect Disconnect the upload menu Command DriveAP User's Manual 4-3 Note (standard user interface only): When DriveAP uploads the connection information of an input pin connected to a parameter with a bit number of 0, DriveAP does not know whether the input pin is connected to bit 0 of the parameter or the entire parameter value. In this case, DriveAP assumes that it is connected to the entire value and deletes the tag 0. If the user knows that it is actually connected to 0, he can click this input pin (while holding down the Ctrl key), write the tag 0 into the tag field of the dialog box displayed on the screen, and then click the OK button. The tag 0 is now displayed in the block diagram. If necessary, you can now modify the AP program on the screen (see "Program Modification" in Chapter 3 "Use of DriveAP"). This command downloads the program on the screen to the connected drive. If necessary, DriveAP will start the download program in the drive after downloading. This command changes the operation mode of DriveAP to online mode (see Chapter 3 - Online Mode in Using DriveAP).
