408368 IAM MODULE DCS模块卡件
表添加/修改注意：
如果您使用AOP将模块配置为从机，则无需手动编辑CLX配置表。仅当使用通用1756模块配置文件时，才需要编辑CLX配置表。接收的数据是从远程主机接收的数据。该数据从字偏移量2开始映射到CLX输入表中。传输数据是从模块发送到远程主机的数据。该数据从字偏移量2.6.4配置表添加开始映射到CLX输出表中。CLX配置表将用于配置从属功能。如果使用Rockwell的AOP进行配置，请参见第6.5.2节，使用附加配置文件（AOP）在RSLogix 5000中配置CLX从机。从配置文件条目从10H（16D）开始。注意：CLX配置文件始终配置为字节位置。对于仅从模式，CLX配置文件的大小必须至少设置为24字节。用户参考指南SST-PB3S-CLX-RLL 40 Slave Functionality©2014 Molex股份有限公司工业产品业务部，集成产品部文件版本：1.0，文件#：715-0109，模板版：1.1，模板ţ：QMS-06-045使用、复制或披露本文件或其中包含的任何信息受本文件第二页的限制。下表显示了支持DP从机功能的CLX配置表的添加：表20：支持DP从设备功能的CLXConfig表的添加名称位置含义/描述AUTORUN本地：
插槽：
C:Data[1]如果2，模块在通电后自动联机，并进入CLX处理器处于的模式（RUN或PROG）ScannerConfig Local:Slot:C:Data[16]此寄存器配置启用从模式。请参阅ScannerConfig Register表（下表）。SlvRxLen Local:Slot:C:Data[17]从机接收数据的长度（大写）SlvTxLen本地：Slot:C:Data[18]从机发送数据的长度。SlvTxOffset Local:Slot:C:Data[20]如果为0，则DP从Tx数据将在字偏移量2处映射到CLX输出文件中。如果设置为非零值，则它将字偏移量指定到应从Tx数据应映射到的CLX输出文件中。Local:Slot:C:Data[21]“LocStn”定义从站的本地站编号。有效范围为1-125。本地波特率：插槽：C:Data[22]“波特率”定义从机的波特率。下表定义了有效的PFB网络速率和写入波特率寄存器的相应值。BAUD速率寄存器值BAUD_9k6 0 BAUD_19k2 1 BAUD_93k75 2 BAUD_187k5 3 BAUD_500k 4 BAUD_1m5 6 BAUD_3m 7 BAUD_6m 8 BAUD_12m 9 BAUD_45k45 11 Reptr Local:Slot:C:Data[23]此选项不适用于仅从模块，可以保留为0。（2）。0如果设置，将使用Profibus ID 0x0876而不是0x0EC7以实现向后兼容性。AUTORUN本地：插槽：C:数据[1]。1如果设置，AUTORUN启用。通电后，从属设备将自动联机。
Note for table addition/modification:
If you use AOP to configure the module as a slave, you do not need to manually edit the CLX configuration table. You need to edit the CLX configuration table only if you are using a generic 1756 module configuration file. The received data is the data received from the remote host. This data is mapped to the CLX input table starting from word offset 2. The transmission data is the data sent from the module to the remote host. This data is mapped to the CLX output table from the word offset 2.6.4 configuration table. The CLX configuration table will be used to configure dependent functions. If Rockwell's AOP is used for configuration, please refer to Section 6.5.2. Use the additional configuration file (AOP) to configure the CLX slave in the RSLogix 5000. The entry from the configuration file starts with 10H (16D). Note: CLX configuration files are always configured as byte locations. For slave only mode, the size of the CLX configuration file must be set to at least 24 bytes. User Reference Guide SST-PB3S-CLX-RLL 40 Slave Functionality © 2014 Molex Co., Ltd. Industrial Product Business Department, Integrated Product Department Document Version: 1.0, Document #: 715-0109, Template Version: 1.1, Template ţ： QMS-06-045 The use, reproduction or disclosure of this document or any information contained therein is restricted by the second page of this document. The following table shows the addition of the CLX configuration table that supports the DP slave function: Table 20: The addition name, location, meaning/description of the CLXConfig table that supports the DP slave function AUTORUN local:
Slot:
C: Data [1] If 2, the module will automatically go online after power on and enter the mode (RUN or PROG) in which the CLX processor is in ScannerConfig Local: Slot: C: Data [16] This register configuration enables slave mode. See the ScannerConfig Register table (below). SlvRxLen Local: Slot: C: Data [17] Length of data received by slave (upper case) SlvTxLen Local: Slot: C: Data [18] Length of data sent by slave. SlvTxOffset Local: Slot: C: Data [20] If it is 0, DP data from Tx will be mapped to CLX output file at word offset 2. If set to a non-zero value, it specifies the word offset to the CLX output file that should be mapped from Tx data. Local: Slot: C: Data [21] "LocStn" defines the local station number of the slave station. The valid range is 1-125. Local baud rate: Slot: C: Data [22] "Baud rate" defines the baud rate of the slave. The following table defines the valid PFB network rate and the corresponding values written to the baud rate register. BAUD Rate Register Value BAUD_ 9k6 0 BAUD_ 19k2 1 BAUD_ 93k75 2 BAUD_ 187k5 3 BAUD_ 500k 4 BAUD_ 1m5 6 BAUD_ 3m 7 BAUD_ 6m 8 BAUD_ 12m 9 BAUD_ 45k45 11 Reptr Local: Slot: C: Data [23] This option is not applicable to slave modules only and can be left as 0. （2）。 0 If set, Profibus ID 0x0876 will be used instead of 0x0EC7 for backward compatibility. AUTORUN local: slot: C: data [1]. 1 If set, AUTORUN is enabled. When power is applied, the slave device will automatically come online.
