3BSE003816R1机器人卡件
此屏幕包括对内部外围卡的控制以及各种中断
从该菜单中，用户还可以确定系统的即插即用是启用还是禁用。注意：此屏幕中的更改可能导致系统故障。如果在进行更改后发现问题，请重新启动系统并访问BIOS。从退出菜单中选择“加载故障保护默认值”并重新启动系统。如果系统故障导致无法访问BIOS屏幕 说明。下面是PCI/PnP菜单的屏幕示例；系统中的选项可能与显示的选项不同。002.53（C）版权所有1985-2002，American Megatrends，股份有限公司.BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Advanced PCI/PnP Settings NO：让BIOS配置系统中的所有设备。是：如果您的系统具有即插即用操作系统，则允许操作系统配置启动时不需要的即插即插（PnP）设备。←→ 选择屏幕↑↓ 选择项目+-更改选项F1常规帮助F10保存并退出ESC退出警告：在以下部分中设置错误的值可能会导致系统故障。即插即用O/S[否]PCI延迟计时器[64]将IRQ分配给PCI VGA[是]调色板侦听[禁用]PCI IDE总线主控器[禁用]非板载PCI/ISA IDE卡[自动]IRQ3[可用]IRQ4[可用]IR Q5[可用]I RQ7[可用]IRQ9[可用]IRQ10[可用]I RQ11[可用]IRQ14[可用]84 B VMIVME-7807/VME-7807RC产品手动引导设置使用引导设置菜单设置引导设备的优先级，包括从远程网络引导。此菜单中显示的设备是POST期间检测到的可引导设备。如果安装的驱动器未显示，请验证硬件安装。此屏幕中还提供了“引导设置”，允许用户设置基本系统的操作方式，例如，支持PS/2鼠标以及是否使用“快速引导”。002.53（C）版权所有1985-2002，American Megatrends，股份有限公司.BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Boot Settings在系统引导期间配置设置。
选择屏幕
择项目输入转到子屏幕F1常规帮助F10保存并退出ESC退出¾引导设置配置¾引导设备优先级¾可移动驱动器85安全设置B安全设置ezPORT设置提供了管理员和用户密码。如果同时使用两个密码，则必须首先设置主管密码。可以对系统进行配置，以便每次系统启动或执行ezPORT设置时，所有用户都必须使用管理员密码或用户密码输入密码。002.53（C）版权所有1985-2002，American Megatrends，股份有限公司.要在忘记密码的情况下重置安全性，必须排空NVRAM并重新配置。要清除CMOS密码：1.关闭设备电源。2.将开关S2位置1移到接通位置。3.等待约5秒。4.将开关S2位置1移到关闭位置。5.给装置通电。当装置重新通电时，CMOS密码将被清除，CMOS将被设置为默认值。BIOS设置实用程序主高级PCIPnP引导安全芯片组退出安全设置安装或更改密码。←→ 选择屏幕↑↓ 选择项目输入更改F1常规帮助F10保存并退出ESC退出主管密码：未安装用户密码：未设置更改主管密码更改用户密码清除用户密码引导扇区病毒防护[已禁用]86 B VMIVME-7807/VME-7807RC产品手册芯片组设置为系统中的芯片组选择各种选项（例如，CPU配置以及北桥和南桥的配置）。芯片组的设置取决于处理器，更改出厂默认设置时必须小心。下面是芯片组设置屏幕的示例；系统上的实际选项可能有所不同。注意：此屏幕中的更改可能导致系统故障。如果在进行更改后发现问题，请重新启动系统并访问BIOS。从退出菜单中选择“加载故障保护默认值”并重新启动系统。如果系统故障导致无法访问BIOS屏幕，请参阅第一章了解清除CMOS的说明。002.53（C）版权所有1985-2002，American Megatrends，股份有限公司.B
This screen includes control of internal and external cards and various interrupts
From this menu, you can also determine whether Plug and Play is enabled or disabled for the system. Note: Changes in this screen may cause system failures. If problems are found after making changes, restart the system and access the BIOS. Select "Load Failsafe Defaults" from the exit menu and restart the system. If a system failure prevents access to the BIOS screen instructions. The following is a screen example of the PCI/PnP menu; The options in the system may differ from those displayed. 002.53 (C) Copyright 1985-2002, American Megatrends, Inc BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Advanced PCI/PnP Settings NO: lets the BIOS configure all devices in the system. Yes: If your system has a Plug and Play operating system, you can allow the operating system to configure Plug and Play (PnP) devices that are not required at startup. ←→ Selection screen ↑↓ Select item+- Change option F1 General help F10 Save and exit ESC Exit warning: Setting wrong values in the following sections may cause system failure. Plug and Play O/S [No] PCI delay timer [64] Assign IRQ to PCI VGA [Yes] palette Listen [Disable] PCI IDE bus master [Disable] non onboard PCI/ISA IDE card [Auto] IRQ3 [Available] IRQ4 [Available] IR Q5 [Available] I RQ7 [Available] IRQ9 [Available] IRQ10 [Available] I RQ11 [Available] IRQ14 [Available] 84 B VMIVME-7807/VME-7807RC product manual boot settings Use the boot settings menu to set the priority of the boot device, including booting from a remote network. The devices displayed in this menu are bootable devices detected during POST. If the installed drive is not displayed, verify the hardware installation. This screen also provides "Boot Settings", which allows users to set the basic system operation mode, such as support for PS/2 mouse and whether to use "Quick Boot". 002.53 (C) Copyright 1985-2002, American Megatrends, Inc BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Boot Settings Configure settings during system boot.
Selection screen
Select an item to enter and go to the sub screen F1 General Help F10 Save and Exit ESC Exit ¾ Boot Settings Configuration ¾ Boot Device Priority ¾ Removable drive 85 security setting B security setting ezPORT setting provides administrator and user passwords. If two passwords are used at the same time, the supervisor password must be set first. The system can be configured so that every time the system starts or performs ezPORT settings, all users must enter a password using either the administrator password or the user password. 002.53 (C) Copyright 1985-2002, American Megatrends, Inc To reset security if you forget your password, you must empty NVRAM and reconfigure it. To clear CMOS password: 1. Turn off the device. 2. Move switch S2 position 1 to the ON position. 3. Wait about 5 seconds. 4. Move switch S2 position 1 to the closed position. 5. Energize the unit. When the device is powered on again, the CMOS password will be cleared and CMOS will be set as the default value. BIOS Setup Utility Main Advanced PCIPnP Boot Security Chipset Exit Security Setup Setup or Change Password. ←→ Selection screen ↑↓ Select an item Enter and change F1 General help F10 Save and exit ESC Exit supervisor password: Not installed user password: Not set Change supervisor password Change user password Clear user password Boot sector virus protection [Disabled] 86 B VMIVME-7807/VME-7807RC product manual Chipset Set Select various options for chipsets in the system (for example, CPU configuration and North Bridge and South Bridge configuration). The chipset settings depend on the processor and care must be taken when changing factory default settings. The following is an example of the chipset setting screen; The actual options on the system may vary. Note: Changes in this screen may cause system failures. If problems are found after making changes, restart the system and access the BIOS. Select "Load Failsafe Defaults" from the exit menu and restart the system. If a system failure prevents access to the BIOS screen, refer to Chapter 1 for instructions on clearing CMOS. 002.53 (C) Copyright 1985-2002, American Megatrends, Inc. B
