9200-06-02-10-00系统模块卡件
规格规格
约为+22°C（+72°F），机壳振动速度为25 mm/s（1 in/s），100 Hz（6000 cpm），10 kΩ 负载，除非另有规定。电灵敏度20 mV/mm/s（500 mV/in/s），正确端接并以校准角度定向时为±5%。校准负载10 kΩ端子“A”至“B”通过引脚“A”和“B”获得的输出灵敏度温度系数0.2%/°C频率响应-参见第8页的“理论速度地震探头频率响应”4.5至1000 Hz（270至60000 CPM）+典型值为0，-3dB。10至1000 Hz（600至60000 CAM）+典型值为0，-3dB。15至1000 Hz（900至60000 CPM）+典型值为0，-3dB。频率响应从最小工作频率（见订购信息）到1 kHz（60000 cpm）+典型值为0，-3dB。有关详细校准数据，请联系Bently Nevada LLC。动态工作范围2.54 mm（0.100 in）峰间最大位移。速度范围25 mm/s（1 in/s）（在+22°C下，100 Hz下，10 kΩ负载，外壳振动。线圈电阻1.25 kΩ±5%锁定线圈电感125 mH，典型振幅线性度±5%，100 Hz（6000CPM）下，0.01至5.0 in/s（0.254至127 mm/s），耐冲击，沿非敏感轴承受50 g峰值最大加速度。在100 Hz和1.0 in/s（2.54 cm/s）下，横向灵敏度为敏感轴灵敏度的最大值±10%。当传感器外壳速度朝向连接器时，输出信号引脚A的极性相对于引脚B为正。
Seismoprobe速度传感器
3300或3500监测器之间的导线长度最大为305米（1000英尺）。请参考手册，了解更长长度的频率衰减。环境限制操作和储存温度：9200:-29°C至+121°C（-20°F至+250°F）。74712:-29°C至+204°C（-20°F至+400°F）。：环境防尘防潮。注意：关于传感器在辐射环境中的操作，请联系您的销售专业人员。相对湿度至95%，不凝结。100%，非浸没式，与整体电缆一起订购时。机械外壳和适配器材料阳极氧化铝A204垫片材料9200：氯丁橡胶74712：硅胶连接器材料顶部和侧面安装选项镀镉铝、氯丁橡胶和镀银铜接线板选项带镀镍铜触点的聚苯硫醚。安装扭矩½-20、¼-20、½-28、5/8-18或M10x1安装底座选项：5.6 Nm（50 in-lb）9200和74712 Seismoprobe速度传感器数据表3/14 141626 Rev.L 8-32螺纹螺柱1.41 Nm（12.5 in-lb）典型物理高度102 mm（4 in）（取决于连接器选项）。直径通常为41 mm（1.6英寸）。重量9200=300克（10.5盎司）。74712=典型的480克（17盎司）。Seismoprobe速度传感器方向所有Seismorobe速度传感器都指定了安装方向，参见“图表
Specifications
Approximately+22 ° C (+72 ° F), casing vibration speed 25 mm/s (1 in/s), 100 Hz (6000 cpm), 10 k Ω load, unless otherwise specified. The electrical sensitivity is 20 mV/mm/s (500 mV/in/s), which is ± 5% when correctly terminated and oriented at the calibration angle. The output sensitivity temperature coefficient 0.2%/° C frequency response obtained by calibrating the load 10 k Ω terminals "A" to "B" through pins "A" and "B" - see "Theoretical speed seismic probe frequency response" 4.5 to 1000 Hz (270 to 60000 CPM) on page 8+typical value is 0, - 3dB. 10 to 1000 Hz (600 to 60000 CAM)+0, - 3dB typical. 15 to 1000 Hz (900 to 60000 CPM)+0, - 3dB typical. Frequency response from minimum operating frequency (see ordering information) to 1 kHz (60000 cpm)+typical value is 0, - 3dB. Contact Bently Nevada LLC for detailed calibration data. Dynamic working range: 2.54 mm (0.100 in) peak to peak maximum displacement. The speed range is 25 mm/s (1 in/s) (at+22 ° C, 100 Hz, 10 k Ω load, and the housing vibrates. The coil resistance is 1.25 k Ω ± 5%, and the coil inductance is 125 mH. The typical amplitude linearity is ± 5%. At 100 Hz (6000 CPM), 0.01 to 5.0 in/s (0.254 to 127 mm/s), it is impact resistant, and it bears 50 g peak maximum acceleration along the non sensitive axis. At 100 Hz and 1.0 in/s (2.54 cm/s), the lateral sensitivity is ± 10% of the maximum sensitivity of the sensitive shaft. When the speed of the sensor housing faces the connector, the polarity of output signal pin A is positive relative to pin B.
Seismoprobe speed sensor
The maximum wire length between 3300 or 3500 monitors is 305 meters (1000 feet). Refer to the manual for longer frequency attenuation. Environmental limitations Operating and storage temperatures: 9200: - 29 ° C to+121 ° C (- 20 ° F to+250 ° F). 74712: - 29 ° C to+204 ° C (- 20 ° F to+400 ° F).: The environment is dust-proof and moisture-proof. Note: Please contact your sales professional about the operation of the sensor in the radiation environment. Relative humidity to 95%, non condensing. 100%, non submerged, when ordered with integral cable. Mechanical housing and adapter material Anodized aluminum A204 Gasket material 9200: Neoprene 74712: Silicone connector material Top and side mounting options Cadmium plated aluminum, Neoprene and silver plated copper terminal block options Polyphenylene sulfide with nickel plated copper contacts. Installation torque ½- 20、 ¼- 20、 ½- 28, 5/8-18 or M10x1 mounting base option: 5.6 Nm (50 in lb) 9200 and 74712 Seismoprobe speed sensor data sheet 3/14 141626 Rev. L 8-32 threaded stud 1.41 Nm (12.5 in lb) typical physical height 102 mm (4 in) (depending on connector option). The diameter is typically 41 mm (1.6 inches). Weight 9200=300 grams (10.5 ounces). 74712=typical 480 g (17 oz). Seismoprobe speed sensor direction All Seismoprobe speed sensors have specified installation direction, see "Diagram
