330104-00-10-10-02-00传感器
3300监测系统机架安装和维护手册
（129766-01）•标准系统的一般说明•三模块冗余（TMR）系统的一般描述•从3300机架上安装和移除模块的说明•3300监测系统3300监测系统框架配置和实用指南（129777-01）中使用的所有电缆的图纸•使用3300机架配置软件设置模块运行参数的指南•使用3300测试实用程序验证模块上的输入和输出端子是否正常运行的指南3300监控系统计算机硬件和软件手册（128158-01）•将机架连接到3300主计算机的说明•程序验证通信•安装软件的程序•使用数据采集/DDE服务器和操作员显示软件的指南•设置网络和远程通信的程序和图表3300现场接线图包（130432-01）•显示如何连接特定传感器的图表•推荐接线列表1.1目视接收检查检查模块是否有明显的运输损坏。
如果运输损坏明显
向承运人提出索赔，并向本特利内华达公司提交一份副本。1.2搬运和储存注意事项电路板包含暴露于静电时容易损坏的设备。由于电路板的明显不当操作造成的损坏将使保修失效。为避免损坏，请遵守以下预防措施。当从机架上卸下该模块时，应用程序警报主机通信和机架配置功能将丢失。•不要将静电放电到电路板上。避免使用会使电路板受到静电损坏的工具或程序。一些可能的原因包括未接地的烙铁、非导电塑料和类似材料。•在处理或维护印刷电路板之前，人员必须用合适的接地带（如3M Velostat No.2060）接地。•用导电袋或箔运输和储存电路板。•在干燥的天气要格外小心。小于30%的相对湿度会增加任何表面上的静电积累。•正确执行时，可在机架通电时将该模块安装到机架中或从机架中卸下。有关正确程序，请参阅机架安装和维护手册（零件号129766-01）。1.3处置声明在产品寿命结束或使用结束时控制产品的客户和第三方全权负责正确处置产品。控制产品的任何个人、公司、公司、协会或机构不得以违反美国州法律、美国联邦法律或任何适用国际法的方式处置产品。本特利内华达公司不负责产品寿命结束或使用结束时的处理
3300 Monitoring System Rack Installation and Maintenance Manual
(129766-01) • General description of standard systems • General description of three module redundant (TMR) systems • Instructions for installing and removing modules from 3300 racks • 3300 Monitoring System 3300 Monitoring System Rack Configuration and Utility Guide (129777-01) Drawings of all cables used in • Guidelines for Setting Module Operating Parameters Using the 3300 Rack Configuration Software • Guidelines for Verifying that the Input and Output Terminals on the Module Work Properly Using the 3300 Test Utility 3300 Monitoring System Computer Hardware and Software Manual (128158-01) • Instructions for connecting the rack to the 3300 host computer • Program verification communication • Program for installing software • Guidelines for using data acquisition/DDE servers and operator display software • Procedures and diagrams for setting up network and telecommunications 3300 Field Wiring Diagram Package (130432-01) • Diagram showing how to connect specific sensors • Recommended wiring list 1.1 Visual receiving inspection Check the module for obvious transport damage.
If transport damage is obvious
Make a claim to the carrier and submit a copy to Bentley Nevada. 1.2 Handling and Storage Precautions The circuit board contains equipment that is easily damaged when exposed to static electricity. Damage caused by obvious improper operation of the circuit board will void the warranty. To avoid damage, observe the following precautions. When the module is removed from the rack, the application alerts host communication and rack configuration functions will be lost. • Do not discharge static electricity onto the circuit board. Avoid using tools or programs that may damage the circuit board by static electricity. Some possible causes include ungrounded soldering irons, non-conductive plastics, and similar materials. • Before handling or maintaining printed circuit boards, personnel must be grounded with a suitable grounding strap (such as 3M Velostat No.2060). • Transport and store circuit boards in conductive bags or foil. • Be extra careful in dry weather. A relative humidity of less than 30% will increase the accumulation of static electricity on any surface. • When performed correctly, the module can be installed in or removed from the rack when the rack is powered up. Refer to the Rack Installation and Maintenance Manual (part number 129766-01) for the correct procedure. 1.3 Disposal Statement Customers and third parties who control the product at the end of its life or use are solely responsible for the correct disposal of the product. Any person, company, company, association or institution that controls the product shall not dispose of the product in a manner that violates U.S. state laws, U.S. federal laws or any applicable international law. Bently Nevada is not responsible for the disposal at the end of product life or use
