DEIF RMC-122D开关量输出模块
从I/O中删除所有24针双探针将INICT01模块连接到NIS模块以外的任何模块的扩展器总线插座。4.将NKTU01、NKTU02、NKTU11或NKTU12电缆的带帽端连接到ICT模块的模块安装单元背板电缆连接器开口。电缆的另一端连接到终端设备或终端安装单元背板。5.滑动ICT模块，同时沿着模块安装单元的顶部和底部导轨引导电路板的顶部和底边缘。6.推动面板，直到模块的后边缘牢固地固定在背板连接器中。7.转动2个锁紧螺钉½圈，将模块锁定到位。当锁紧螺钉上插槽的开口端朝向面板中心时，模块锁定到位。有关完整的终端设备信息，请参阅NTMF01终端单元或NIMF01和NIMF02终端模块说明。附录C和D提供了有关这些终端设备的快速参考信息。在模块安装单元背板上安装双探针之前，请断开电源。否则将导致与机柜区域接触，可能导致严重或致命的电击。AVERTISSEMENT Interrompez l‘alimentation avant d‘installer des dipphunts sur le fond de panier du chassis de montage des modules。西农，请你联系我们，告诉我们你的美人有没有被电击的危险。
INICT03 INFI-NET到计算机传输模块配置
安装一个INICT03 INFI-NET到计算机传输模块（ICT）、一个IMMPI01多功能处理器接口模块（MPI）和一个NIS模块，以形成INICT03INFI-NET到计算机接口。注：INICT03模块使用到模块安装单元背板的连接，该背板在早期网络90系统中起到其他功能。为避免潜在的模块损坏，请在安装模块之前评估系统的兼容性：早期网络90系统对模块接头P1的引脚3和引脚4施加-30 VDC电压。INFI 90模块不需要此电压。在INFI 90系统中，引脚4用于Controlway总线。如果您的系统包含需要-30 VDC的模块，请将跨接线J5设置到30 VDC位置。这样可以将ICT模块安装在使用-30 VDC的模块安装单元中，并限制与模块总线的通信。双列直插式开关设置ICT模块由一块电路板组成。该板有四个双列直插式开关。这些双列直插式开关可选择模块操作选项、串行端口通信特性和波特率。图3-4显示了双列直插式开关的位置。在使用MPI模块安装ICT模块时，模块安装单元内的模块放置非常重要。使用ICT模块安装MPI模块需要模块安装单元中的两个相邻插槽。ICT模块必须占据右侧插槽（当面向模块安装单元的前部时），MPI模块必须占据左侧插槽。
Remove any 24-pin dipshunts from the I/O
expander bus sockets that would connect the INICT01 module to any module other than the NIS module. 4. Attach the hooded end of the NKTU01, NKTU02, NKTU11, or NKTU12 cable to the module mounting unit backplane cable connector opening for the ICT module. The other end of the cable attaches to the termination device or to the termination mounting unit backplane. 5. Slide the ICT module in while guiding the top and bottom edges of the circuit boards along the top and bottom rails of the module mounting unit. 6. Push on the faceplate until the rear edges of the module are firmly seated in the backplane connectors. 7. Turn the 2 latch screws ½ turn to lock the module in place. The module is locked into place when the open end of the slot on the latching screws face the center of the faceplate. Refer to the NTMF01 termination unit or NIMF01 and NIMF02 termination module instruction for complete termination device information. Appendix C and D provide quick reference information about these termination devices.Disconnect power before installing dipshunts on the module mounting unit backplane. Failure to do so will result in contact with cabinet areas that could cause severe or fatal shock. AVERTISSEMENT Interrompez l'alimentation avant d'installer des dipshunts sur le fond de panier du châssis de montage des modules. Sinon, tout contact avec cette zone entraîne des risques d'lectrocution sérieuse ou fatale.
INICT03 INFI-NET TO COMPUTER TRANSFER MODULE CONFIGURATION
Install one INICT03 INFI-NET to Computer Transfer Module (ICT), one IMMPI01 Multi-Function Processor Interface Module (MPI), and one NIS module to make an INICI03 INFI-NET to Computer Interface. NOTE: The INICT03 module uses connections to the module mounting unit backplane that served other functions in early Network 90 systems. To avoid potential module damage, evaluate your system for compatibility prior to module installation: Early Network 90 systems applied -30 VDC to pins 3 and 4 of the module connector P1. This voltage is not required for INFI 90 modules. In INFI 90 systems, pin 4 is used for the Controlway bus. If your system contains modules that require -30 VDC, set jumper J5 to the 30 VDC position. Doing so allows the installation of the ICT module in a module mounting unit that uses -30 VDC and limits communication to the module bus. Dipswitch Settings The ICT module consists of one circuit board. The board has four dipswitches. These dipswitches select module operation options, serial port communication characteristics and baud rate. Figure 3-4 shows the dipswitch locations. Module placement within the module mounting unit is important when installing an ICT module with the MPI module. Installing an MPI module with the ICT module requires two adjacent slots in a module mounting unit. The ICT module must occupy the right slot (when facing the front of the module mounting unit) and the MPI module must occupy the left slot.
产品优势
1：国外专业的供货渠道，具有价格优势
2：产品质量保证，让您售后无忧
3：全国快递包邮
4：一对一服务
公司主营范围简介
PLC可编程控制器模块，DCS卡件，ESD系统卡件，振动监测系统卡件，汽轮机控制系统模块，燃气发电机备件等，优势品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件、欧美进口模块。
产品广泛应用于冶金、石油天然气、玻璃制造业、铝业、石油化工、煤矿、造纸印刷、纺织印染、机械、电子制造、汽车制造、塑胶机械、电力、水利、水处理/环保、锅炉供暖、能源、输配电等等
