产品详情介绍
Honeywell 51305896-100输出控制卡
安装连接器板工具和实用工具螺丝刀，开槽0.8 x 4.0 mm匹配连接器板安装连接器板1。将连接器板插入导轨，凹槽朝上（参见下图）。将槽安装到导轨销中。2.将连接器板放在电缆屏蔽轨道上。3.将两个外加螺钉固定到底板上。首先拧入下部螺钉，然后拧入上部螺钉。要卸下连接器板1，请从基板上松开固定螺钉。2.从电缆屏蔽轨道上提起连接器板的下部。3.从导轨上拆下连接器板。安装和拆卸模块本章介绍如何安装和拆卸HIMax模块。可以在HIMax系统运行时安装和卸下模块。注意：模块卡住会损坏总线和电源插座！不遵守这一点可能会损坏控制器。将模块插入底板时务必小心。工具和工具螺丝刀，开槽0.8 x 4.0 mm螺丝刀，开槽1.2 x 8.0 mm
默认网关的IP地址。ARP老化时间[s]处理器或COM模块将通信伙伴的MAC地址存储在MAC/IP地址分配表（ARP缓存）中。如果在1x….2x ARP老化时间……的时间段内收到通信的消息，MAC地址仍存储在ARP缓存中。…没有收到通信伙伴的消息，MAC地址从ARP缓存中删除。本地网络中ARP老化时间的典型值范围为5…300秒。用户无法读取ARP缓存的内容。值范围：1…3600 s默认值：60 s
在SILVorX中配置模块
处理器模块在SILworX硬件编辑器中配置。必须配置处理器模块的以太网接口。以下各章介绍了详细视图选项卡。请确保正确设置IP地址！如果使用路由器或网关，由于双向传输需要额外的时间，用户必须调整（增加）ARP老化时间。如果ARP老化时间过低，通信伙伴的MAC地址将从ARP缓存中删除，通信将延迟或中断。为了获得高效的性能，ARP老化时间值必须小于为所用协议设置的接收超时。
MAC学习和ARP老化时间用于设置以太网交换机学习MAC地址的速度。可以进行以下设置：保守（建议）：如果ARP缓存已经包含通信伙伴的MAC地址，则这些地址将被锁定，并且在至少一个ARP老化时间和最多两个ARP衰老时间段内，不能被其他MAC地址替换。这确保了数据包不会被有意或无意地转发给外部网络参与者（ARP欺骗）。容差：当接收到消息时，消息中包含的IP地址与ARP缓存中的数据进行比较，存储在ARP缓存的MAC地址立即被消息中的MAC地址覆盖。如果通信的可用性比控制器的授权访问更重要，则必须使用容差设置。默认设置：保守
Mounting a Connector Board
Tools and utilities Screwdriver, slotted 0.8 x 4.0 mm Matching connector board To install the connector board 1. Insert the connector board into the guiding rail with the groove facing upwards (see following figure). Fit the groove into the guiding rail pin. 2. Place the connector board on the cable shield rail. 3. Secure the two captive screws to the base plate. First screw in the lower than the upper screw. To remove the connector board 1. Release the captive screws from the base plate. 2. Lift the lower section of the connector board from the cable shield rail. 3. Remove the connector board from the guiding rail.Mounting and Removing the Module This chapter describes how to mount and remove the HIMax module. A module can be mounted and removed while the HIMax system is operating. NOTICE Damage to bus and power sockets due to module jamming! Failure to observe this can damage the controller. Always take care when inserting the module in the base plate.Tools and utilities Screwdriver, slotted 0.8 x 4.0 mm Screwdriver, slotted 1.2 x 8.0 mm
IP address of the default gateway. ARP Aging Time [s] A processor or COM module stores the MAC addresses of the communication partners in a MAC/IP address assignment table (ARP cache). If in a period of 1x....2x ARP Aging Time ... ... messages of the communication are received, the MAC address remains stored in the ARP cache. ... no messages of the communication partner are received, the MAC address is erased from the ARP cache. The typical value for the ARP Aging Time in a local network ranges from 5...300 s. The user cannot read the contents of the ARP cache. Range of values: 1...3600 s Default value: 60 s
Configuring the Module in SILWorX
The processor module is configured in the SILworX Hardware Editor. The Ethernet interface of the processor module must be configured. Each of the following chapters describes a detail view tab. Ensure proper setting ot the IP address!If routers or gateways are used, the user must adjust (increase) the ARP Aging Time due to the additional time required for twoway transmission. If the ARP Aging Time is too low, the MAC address of the communication partner is erased from the ARP cache, the communication is delayed or interrupted. For an efficient performance, the ARP aging time value must be less than the receive timeout set for the protocols in use.
MAC Learning and ARP Aging Time are used to set how quick the Ethernet switch should learn the MAC address. The following settings are possible: Conservative (recommended): If the ARP cache already contains MAC addresses of communication partners, these are locked and cannot be replaced by other MAC addresses for at least one ARP Aging Time and a maximum of two ARP Aging Time periods. This ensures that data packets cannot be intentionally or unintentionally forwarded to external network participants (ARP spoofing). Tolerant: When a message is received, the IP address contained in the message is compared to the data in the ARP cache and the MAC address stored in the ARP cache is immediately overwritten with the MAC address from the message. The Tolerant setting must be used if the availability of communication is more important than the authorized access to the controller. Default setting: Conservative
产品优势
1：国外专业的供货渠道，具有价格优势
2：产品质量保证，让您售后无忧
3：全国快递包邮
4：一对一服务
公司主营范围简介
PLC可编程控制器模块，DCS卡件，ESD系统卡件，振动监测系统卡件，汽轮机控制系统模块，燃气发电机备件等，优势品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件、欧美进口模块。
产品广泛应用于冶金、石油天然气、玻璃制造业、铝业、石油化工、煤矿、造纸印刷、纺织印染、机械、电子制造、汽车制造、塑胶机械、电力、水利、水处理/环保、锅炉供暖、能源、输配电等等
