产品内容介绍
SCHENCK A909001.02控制器
连接方式当输出电压超过额定值时，请确保最大输出功率低于额定值。此外，当输出电压低于额定值时，请确保最大输出电流低于额定值。使用时请考虑以下特性。*可调输出电压在输出的20%（3V型号：30%）内（小于PV电压的1V）与PV电压成正比，并具有线性特性。然而，对于输出电压在输出电压的10%以内（约小于光伏电压的0.5V），输出将进入间歇模式，纹波电压变大，电源也会发出不规则的声音。然而，这不是损害。也会有欠压闭锁保护功能触发电源关闭的情况。输出关闭时，低输出检测功能（PF）触发PF信号并将其设置为“H”，同时输出LED关闭。在电压锁定保护模式下，关闭输入几分钟，然后再次打开输入进行恢复。通过将远程ON/OFF控制信号转到OFF和ON，也可以从欠压锁定中恢复。欠压检测值使用自动跟踪模式，该模式跟随输出电压，并在保护功能模式下始终对应输出电压的70%-80%。基于上述解释，我们将不在产品保修范围内使用输出电压20%以内的可调输出电压。对于要求输出电压在20%以内变化的应用，请在操作前考虑以上内容。对于要求输出电压低于20%的应用，由于用户系统的应用类型不同，可能存在与上述不同的情况（行为）。因此，请与用户系统核实。
输出峰值电流
对于输出峰值电流的型号，请满足以下条件。根据第6-1节中的输出降额降低峰值电流值。当额定电流和连续峰值输出时间（τ）在使用过程中超过额定值时，保护电路会关闭输出。当保护电路激活时，输入被暂时切断几分钟，然后重新输入电源或输入远程ON/off控制信号以恢复输出。输入电压范围：AC180V-265V连续峰值输出时间（τ）：10秒内峰值输出电流（Ip）：额定峰值输出电流内安装方向如下。标准安装方法为（A）。方法（B）、（C）和（D）也是可行的。禁止使用（A）、（B）、（C）和（D）以外的安装方法（例如：（E）和（F））。
安装方法注意事项（1）此电源设备是一个带有内置风扇的强制空气冷却系统。（2） 该电源在前面板和后面板上有通风孔。保持这些区域与前侧的距离大于100mm，与后侧的距离大于50mm。（3） 请注意，在多尘环境中，通风会恶化。（4） 内置风扇是寿命有限的部件，需要定期更换。（更换将收费）。（5） 该电源的环境温度与正面中心的距离小于50mm。（6） 安装螺钉的最大允许穿透深度为6mm。安装螺钉的螺纹不完整不得穿透。（7） 安装螺钉（M4）的建议扭矩为1.27 N∙m。
Connection method
When output voltage is over rated value, please make sure that maximum output power is below rated value. Moreover, when output voltage is below rated value, please make sure that maximum output current is below rated value. Please consider the following characteristic during usage.* Adjustable output voltage within 20%(3Vmodel : 30%) of output (less than 1V of PV voltage) is proportional to PV voltage and has a linear characteristic. However, for output voltage within 10% of output (about less than 0.5V of PV voltage), output will go into intermittent mode and ripple voltage becomes large, also irregular sound is release from the power supply. However, it is not damage. There will also be cases of the power supply shutting down triggered by under voltage lock out protection function. With output shutting down, low output detection function (PF) triggers the PF signal and set it to "H", and also output LED is switch off. Under voltage lock out protection mode, switch off input for a few minutes and then switch on input again for recovery. Recovery from under voltage lock out is also possible by turning remote ON/OFF control signal OFF and ON. Under voltage detection value uses an automatic tracking mode, which follows the output voltage and constantly correspond to the 70%-80% of output voltage with a protection function mode. Base on the explanation above, we will kindly exclude the usage of adjustable output voltage within 20% of the output voltage from the product warranty. For application that requires variable output voltage within 20% of output voltage, please kindly consider the above contents prior to operation. For application that requires output voltage below 20%, due to different type of application for the user's system, there might be a situation (behavior) different from the one mentioned above. Therefore please check with the user system.
Output peak Current
For model with output peak current, please meet the following condition. Reduce peak current value according to output derating as section 6-1. The output is shut down by protection circuit when rated current and continuous peak output time (τ) exceeds rated value during usage. When protection circuit is activated, input is temporarily cut off for a few minutes and then power is re-input or remote ON/OFF control signal should be input for recovery of the output. Input voltage range ：AC180V - 265V Continuous Peak output time(τ) ：Within 10 seconds Peak output current(Ip) ：Within the rated peak output current Mounting directions are as follows. Standard mounting method is (A). Methods (B), (C) and (D) are also possible. Mounting methods besides (A),(B),(C) and (D) (example : (E) and (F)) are inhibit.
Mounting Method Caution (1) This Power supply unit is a forced air-cooling system with a built-in fan. (2) This power supply has ventilating holes on the front and back panels. Keep these areas freely more than 100mm from front side and more than 50mm from rear side. (3) Please note that ventilation will be worsened in a dusty environment. (4) Built-in fan is limited life part, which require periodic replacement. (Replacement will be charge). (5) The ambient temperature of this power supply is less than 50mm from the center of a front side. (6) The maximum allowable penetration of mounting screw is 6mm. Incomplete thread of mounting screw should not be penetrated. (7) Recommended torque for mounting screw (M4) is 1.27 N･m.
产品优势
1：国外专业的供货渠道，具有价格优势
2：产品质量保证，让您售后无忧
3：全国快递包邮
4：一对一服务
公司主营范围简介
PLC可编程控制器模块，DCS卡件，ESD系统卡件，振动监测系统卡件，汽轮机控制系统模块，燃气发电机备件等，优势品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件、欧美进口模块。
产品广泛应用于冶金、石油天然气、玻璃制造业、铝业、石油化工、煤矿、造纸印刷、纺织印染、机械、电子制造、汽车制造、塑胶机械、电力、水利、水处理/环保、锅炉供暖、能源、输配电等等
