产品内容介绍
Schumacher 1483-0401A VMDTEOSAVP控制器
内存、时钟、触摸面板和功能开关简介注释： 当显示指示电池电量低的消息时，为面板供电并给电池充满电。24小时内，电池充电至允许备用操作的水平。完成完全充电需要大约120小时（五天）。 当电池的环境温度为40°C（104°F）或更低时，可充电锂电池的寿命为10年；当电池环境温度为50°C（122°F）或者更低时，寿命为4.1年；当蓄电池环境温度为60°C（140°F）和更低时，其寿命为1.5年。用于备份时： 电池充满电约100天。 使用半充电电池约6天*1根据面板的工作温度和使用年限，时钟可能会从-380秒/月偏离至+90秒/月。对于这种精度水平不足的系统，用户应在需要失去通信时进行监控和调整 通信端口的所有连接不得对端口施加过大压力。 将通信电缆牢牢连接到面板或机柜。 仅使用状态良好的锁定系统的D-Sub 9针电缆。不遵守这些说明可能导致人身伤害或设备损坏。电击当使用SG端子将外部设备连接到面板时： 设置系统时，请确认没有创建短路回路。 对于HMIGTO1300，当主机（PLC）单元未隔离时，将#5 SG终端连接到远程设备。将#5 SG端子连接至已知可靠的接地连接，以降低损坏电路的风险。 对于HMIGTO1310，当主机（PLC）单元未隔离时，将#8 SG端子连接到远程设备。将#8 SG端子连接至已知可靠的接地连接，以降低损坏电路的风险。不遵守这些说明将导致死亡或重伤
串行接口COM2规格
简介注：有关如何连接控制器和其他类型设备的信息，请参阅屏幕编辑软件的相应设备驱动程序手册。串行端口未隔离。SG（信号接地）和FG（机架接地）端子连接在面板内。串行接口COM2 HMIGTO1300:通过RS-485电缆的RJ45连接器注：设置RS-485通信时，某些设备的电缆图可能需要终端侧极化。该终端不需要任何特殊设置，因为它可以自动处理极化。电击当使用SG端子将外部设备连接到面板时： 设置系统时，请确认没有创建短路回路。 当主机（PLC）单元未隔离时，将#8 SG终端连接到远程设备。将#8 SG端子连接至已知可靠的接地连接，以降低损坏电路的风险。不遵守这些说明将导致死亡或重伤。所有上述值的设计都考虑了电缆弯曲。此处给出的尺寸是典型值，取决于使用的连接电缆类型。因此，这些值仅供参考。所有上述值的设计都考虑了电缆弯曲。此处给出的尺寸是典型值，取决于使用的连接电缆类型。因此，这些值仅供参考。
Memory, Clock, Touch Panel, and Function Switches
Introduction NOTE: When the message indicating that the battery level is low is displayed, supply power to the panel and fully charge the battery. In 24 hours the battery charges to a level that allows backup operation. Completing a full charge requires about 120 hours (five days). The lifetime of the rechargeable lithium battery is 10 years when the battery’s ambient temperature is 40 °C (104 °F) or less, 4.1 years when the battery’s ambient temperature is 50 °C (122 °F) or less, and 1.5 years when the battery’s ambient temperature is 60 °C (140 °F) or less. When used for backup: Approximately 100 days with a fully charged battery. Approximately 6 days with a half-charged battery *1 Depending on the operating temperature and age of panel, the clock can deviate from -380 to +90 sec/month. For systems where this level of precision is insufficient, the user should monitor and make adjustments when required LOSS OF COMMUNICATION All connections to the communication ports must not put excessive stress on the ports. Securely attach communication cables to the panel or cabinet. Use only D-Sub 9-pin cables with a locking system in good condition. Failure to follow these instructions can result in injury or equipment damage.ELECTRIC SHOCK When using the SG terminal to connect an external device to the panel: Verify that a short-circuit loop is not created when you set up the system. For HMIGTO1300, connect the #5 SG terminal to remote equipment when the host (PLC) unit is not isolated. Connect the #5 SG terminal to a known reliable ground connection to reduce the risk of damaging the circuit. For HMIGTO1310, connect the #8 SG terminal to remote equipment when the host (PLC) unit is not isolated. Connect the #8 SG terminal to a known reliable ground connection to reduce the risk of damaging the circuit. Failure to follow these instructions will result in death or serious injury
Specifications of Serial Interface COM2
Introduction NOTE: For information on how to connect controllers and other types of equipment, refer to the corresponding device driver manual of your screen editing software. The serial port is not isolated. The SG (signal ground) and FG (frame ground) terminals are connected inside the panel. Serial Interface COM2 HMIGTO1300: RJ45 connector via an RS-485 cable NOTE: When setting up RS-485 communication, the cable diagram for some equipment may require polarization on the terminal side. This terminal does not require any special setting as it handles polarization automatically.ELECTRIC SHOCK When using the SG terminal to connect an external device to the panel: Verify that a short-circuit loop is not created when you set up the system. Connect the #8 SG terminal to remote equipment when the host (PLC) unit is not isolated. Connect the #8 SG terminal to a known reliable ground connection to reduce the risk of damaging the circuit. Failure to follow these instructions will result in death or serious injury.All the above values are designed with cable bending in mind. The dimensions given here are representative values depending on the type of connection cable in use. Therefore, these values are intended for reference only All the above values are designed with cable bending in mind. The dimensions given here are representative values depending on the type of connection cable in use. Therefore, these values are intended for reference only.
公司主营产品图展示
产品优势
1：国外专业的供货渠道，具有价格优势
2：产品质量保证，让您售后无忧
3：全国快递包邮
4：一对一服务
公司主营范围简介
PLC可编程控制器模块，DCS卡件，ESD系统卡件，振动监测系统卡件，汽轮机控制系统模块，燃气发电机备件等，优势品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件、欧美进口模块。
产品广泛应用于冶金、石油天然气、玻璃制造业、铝业、石油化工、煤矿、造纸印刷、纺织印染、机械、电子制造、汽车制造、塑胶机械、电力、水利、水处理/环保、锅炉供暖、能源、输配电等等
