产品内容介绍
CUTLER HAMMER 5785T 92-02016-00终端控制模块
输入信号类型选择每个输入可以与电流或电压信号一起使用。选择由位于NAIO顶盖后面的DIP开关制成模块外壳（见图3-1）。开关设置如下所示。独立于信号类型的选择模拟输入以mA显示在ACS 600控制面板上；e、 g.10 V将显示为20 mA。必须考虑到这一点缩放信号或读取模拟的实际值时输入端AI2和AI3。有关更多信息，请参阅驱动器手册。0.5至1.5 mm2双绞线，单独和/或整体模拟信号应使用屏幕。屏幕应为连接至NAIO模块上的SHF端子。参见示例下图。X1和X2具有单独的RC滤波器，如上图所示，即一个接线板上的SHF端子连接在一起，然后连接至通过RC滤波器接地。
注意：不要将信号电缆与电源电缆平行布线。
编程模块和驱动器之间的通信由驱动参数。（确保参数设置与模块的模式开关设置。）激活后，NAIO替换某些标准输入和输出。请参阅驱动器固件手册，参数组98。
3.0及以下版本的标准应用程序用户应参考
有关驱动参数列表，请参见附录E。
注意：新设置仅在模块下次通电。
NAIO模块
替换NAIO-03可用于更换有故障的NAIO-01/02，NAIO类型的差异详见附录E.I/O扩展链路兼容设备：NAIO模块、NDIO模块、NTAC模块、ACS 600变频器
链路最大大小：128个站点
拓扑：环形
串行通信类型：异步
传输速度：1 Mbit/s协议：ABB分布式驱动通信系统（DDCS）
介质访问控制方法：
•ACS 600投票的应用和电机控制委员会（NAMC）其他车站周期性电缆：光纤电缆
•结构：塑料芯，直径1mm，塑料护套夹克
•电缆衰减：0.23 dB/m
•电缆最大长度：两站之间10 m外壳：塑料，尺寸：45 mm x 75 mm x 105 mm
防护等级：IP 20
安装：安装在标准安装导轨上硬件设置：七个DIP开关用于设置节点编号。分配的节点号：16（默认）。
连接器：
•用于ACS 600连接
•两个螺钉接线板（Phoenix Contact MVBSTW 2,5/8-ST5,08），用于编码器和电源连接。导线横截面积：0.5至2.5 mm2
Input Signal Type Selection
Each input can be used with a current or voltage signal. The selection is made with a DIP switch located behind the top lid of the NAIO module casing (see Figure 3-1). The switch settings are shown below.Independent of the selection of the signal type, the values of the analogue inputs are displayed in mA on the ACS 600 Control Panel; e.g. 10 V will be displayed as 20 mA. This must be taken into account when scaling the signals or reading the actual value of the analogue inputs AI2 and AI3. See the drive manuals for more information.0.5 to 1.5 mm2 twisted pair cables with individual and/or overall screens should be used for analogue signals. The screens should be connected to the SHF terminals on the NAIO module. See the example below.X1 and X2 have separate RC filters as pictured above, i.e. the SHF terminals on one terminal block are connected together, then to earth through an RC filter. Note: Do not route the signal cables parallel to power cables. Programming The communication between the module and the drive is activated by a drive parameter. (Ensure that the parameter settings correspond to the mode switch setting of the module.) After activation, the NAIO replaces certain standard inputs and outputs. See the drive Firmware Manual, Parameter Group 98. Users of Standard Application Program versions up to 3.0 should refer to Appendix E for a listing of related drive parameters. Note: The new settings take effect only the next time the module is powered up. NAIO Module Replacement An NAIO-03 can be used to replace a faulty NAIO-01/02. For reference, the differences of the NAIO types are detailed in Appendix E.
I/O Extension Link
Compatible Devices: NAIO module, NDIO module, NTAC module, ACS 600 frequency converter Maximum size of the link: 128 stations Topology: Ring Serial communication type: Asynchronous Transmission speed: 1 Mbit/s Protocol: ABB Distributed Drives Communication System (DDCS) Medium access control method: • Application and Motor Control Board (NAMC) of the ACS 600 polls other stations cyclically Cable: Fibre optic cable • Construction: Plastic core, diameter 1 mm, sheathed with plastic jacket • Cable attenuation: 0.23 dB/m • Cable maximum length: 10 m between two stations
Enclosure: Plastic, dimensions: 45 mm x 75 mm x 105 mm. Degree of protection: IP 20 Mounting: Onto a standard mounting rail Hardware settings: Seven DIP switches for setting the node number. Allocated node number: 16 (default). Connectors: • Light transmitter and receiver (Hewlett-Packard Versatile Link) for ACS 600 connection • Two screw terminal blocks (Phoenix Contact MVBSTW 2,5/8-ST5,08) for encoder and power supply connections. Conductor crosssectional area: 0.5 to 2.5 mm2
公司主营产品图展示
产品优势
1：国外专业的供货渠道，具有价格优势
2：产品质量保证，让您售后无忧
3：全国快递包邮
4：一对一服务
公司主营范围简介
PLC可编程控制器模块，DCS卡件，ESD系统卡件，振动监测系统卡件，汽轮机控制系统模块，燃气发电机备件等，优势品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件、欧美进口模块。
产品广泛应用于冶金、石油天然气、玻璃制造业、铝业、石油化工、煤矿、造纸印刷、纺织印染、机械、电子制造、汽车制造、塑胶机械、电力、水利、水处理/环保、锅炉供暖、能源、输配电等等
