产品内容介绍
ADEPT 10350-01064R数据采集板
如果您没有设置上述自动方法以启用在ADC之后，DeviceLogix仍然可以手动执行此操作。启用DeviceLogix程序，将DeviceLogix参数53-[DLX操作]设置为“0”（启用逻辑）使用以下方法之一：
•Logix程序中写入参数的明确消息。
•用于设置参数的HIM或驱动软件工具。
注意，在将DeviceLogix参数53设置为“0”（启用逻辑）后将由驱动器更改为“6”（逻辑启用），以指示操作状态。请勿在中将DeviceLogix参数53-[DLX Operation]设置为“0”（启用逻辑）将配置保存到控制器。此设置将锁定模块并阻止写入更高的编号的参数，从而导致ADC下载失败。
固件管理器不能用于更新20-750-S1安全速度监测器模块固件。这是由于其独特的升级组件安全核心。
可以使用ControlFLASH（1203-USB）手动升级串行转换器和相应的升级文件使用20-750-S1安全速度监视器模块时的特殊注意事项在使用具有20-750-S1安全速度的ADC时，有一些特殊的注意事项监测器模块。
安全性要求用户在驱动器可以运行。尽管需要手动“步骤”，ADC仍然可以使用。
除了安全速度监视器模块的配置外模块密码存储在控制器的配置脚本中并用作连接过程的一部分，以允许将配置存储在要下载到模块的控制器。
此密码需要输入驱动器模块中安全速度监视器模块的配置文件RSLogix 5000软件中的属性对话框。此密码值是输入控制器上安全速度监视器模块的参数13下载到模块，这是程序所要求的用户，以便将来与模块交互时使用。使用此密码时将来，它将被输入安全速度监视器的参数1。
不要设置安全速度监视器模块参数5[锁定状态]至“1”（锁定）；或参数6[操作模式]至“1”（运行），然后保存控制器的配置。设置这些参数将锁定模块并防止写入较高编号参数，从而导致ADC下载失败。
这两个在执行上传或下载ADC后。要使用现有配置的Safe，可能需要以下手动步骤速度监视器模块（例如，更换驱动器并重新使用现有的模块），以允许控制器下载配置至安全速度监视器模块。
（注意，这些手动步骤可能需要将以太网电缆与驱动器断开连接，作为控制器的尝试配置安全速度监视器模块将包括锁定来自其他来源的写入，如HIM）。
If you do not set up the automatic method described above to enable DeviceLogix after ADC, you can still do so manually. To enable the DeviceLogix program, set DeviceLogix Parameter 53 - [DLX Operation] to “0” (Enable Logic) by using one of these methods: • An explicit message in the Logix program to write to the parameter. • A HIM or drive software tool to set the parameter. Note that after setting DeviceLogix Parameter 53 to “0” (Enable Logic), the value will be changed by the drive to “6” (Logic Enabled) to indicate operation status.Do not set DeviceLogix parameter 53 - [DLX Operation] to “0” (Enable Logic) in the Add-on Profile configuration before saving the configuration to the controller. This setting would lock the module and prevent writing the higher numbered parameters, thus causing the ADC download to fail.Firmware Supervisor cannot be used to update the 20-750-S1 Safe Speed Monitor Module firmware. This is due to unique upgrade components with its safety core. It can be manually upgraded using ControlFLASH, a 1203-USB Serial Converter, and the appropriate upgrade file Do not set Safe Speed Monitor Module parameter 5 [Lock State] to “1” (Lock); or parameter 6 [Operating Mode] to “1” (Run) in the Add-on Profile configuration before saving the configuration to the controller. Setting these parameters would lock the Module and prevent writing the higher numbered parameters, thus causing the ADC download to fail. These two parameters need to be changed manually after performing an upload or after the ADC download.
Special Considerations
When Using a 20-750-S1 Safe Speed Monitor Module There are special considerations when using ADC with the 20-750-S1 Safe Speed Monitor Module. Safety requires manual intervention by the user before the drive can become operational. Although a manual ‘step’ is required, ADC can still be used. In addition to the configuration of the Safe Speed Monitor Module, the password for the Module is stored in the configuration script in the controller and used as part of the connection process to allow the configuration stored in the controller to be downloaded to the Module. This password will need to be entered into the profile for the Safe Speed Monitor Module in the drive’s Module Properties dialog box in RSLogix 5000 software. This password value is the value entered in parameter 13 of the Safe Speed Monitor Module on controller download to the Module, which is required by procedure to be recorded by the user for future use when interacting with the Module. When using this password in the future, it would be entered into parameter 1 for the Safe Speed Monitor
The following manual steps may be needed to take an existing configured Safe Speed Monitor Module (for example, replacing the drive and reusing the existing Module) out of Run mode to allow the controller to download the configuration to the Safe Speed Monitor Module. (Note that these manual steps may need to be performed with the Ethernet cable disconnected from the drive as the controller’s attempts to configure the Safe Speed Monitor Module will include locking out writes from other sources, such as the HIM).
公司主营产品图展示
产品优势
1：国外专业的供货渠道，具有价格优势
2：产品质量保证，让您售后无忧
3：全国快递包邮
4：一对一服务
公司主营范围简介
PLC可编程控制器模块，DCS卡件，ESD系统卡件，振动监测系统卡件，汽轮机控制系统模块，燃气发电机备件等，优势品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件、欧美进口模块。
产品广泛应用于冶金、石油天然气、玻璃制造业、铝业、石油化工、煤矿、造纸印刷、纺织印染、机械、电子制造、汽车制造、塑胶机械、电力、水利、水处理/环保、锅炉供暖、能源、输配电等等
