产品内容介绍
XYCOM 9487-47B1319210000连接控制终端
4.02版驱动器AOP需要用户操作才能启用ADC。这有助于验证用户在打开ADC之前了解ADC操作。请注意使用4.02版（或更高版本）驱动器AOP时，ADC工作状态如下：
•添加新驱动器时，对于任何支持ADC，例如固件为7.001或更高版本的PowerFlex 753驱动器，或固件为4.001或更高版本的PowerFlex 755驱动器。
•将早期的RSLogix 5000项目转换为版本20.00时已使用4.02（或更高版本）Drive AOP或更新使用4.01版驱动器AOP创建的项目时，任何ADC对于支持ADC的驱动器，设置将按原样传递。对于例子：
–如果在以前的项目中对某个驱动器禁用了ADC，它将保留残废
–如果使用4.01版驱动器AOP的驱动器启用了ADC，并且项目后来更新到4.02（或更高版本）Drive AOP，它将保持启用状态。
通过相应的端口属性对话框管理外围设备的键控每个外围设备的框。
嵌入式EtherNet/IP适配器的电子键控（仅端口13PowerFlex 755驱动器上）和DeviceLogix（端口14）端口被“禁用”默认情况下。
两个端口都没有单独的固件，目前由驱动器固件（端口0）管理。如果将其中之一设置为“完全匹配”，固件主管将无法找到升级安装过程中的文件。如果“外围设备驱动连接故障”复选框被选中，并且在连接到时出现不匹配或故障或者配置这两个端口，整个ADC进程将失败将与驱动器进行I/O连接。
HIM和串行转换器（1203-SSS和1203）的电子钥匙-USB）默认禁用。
这些通常是临时设备或仅用于监控目的，因此，如果是否存在。
您仍然可以选择将这些设置为其他键控选择（如果需要）。兼容模块此选择是不使用固件管理器时的典型ADC选择。
A.更换驱动器（包括外围设备）需要具有相同或更高的固件版本与原始版本相同。由于需要更新固件的驱动器与旧固件兼容，这允许ADC在不兼容的情况下工作关注点。请注意，如果系列更改伴随着主要固件更改，则替换驱动器可能与键控“兼容”，也可能不兼容。
禁用使用ADC时，通常不应使用此选项。此选择允许更换驱动器以具有任何不同的主（X.xxx）和/或次（X.xx）固件修订由用户提供具有固件版本的更换件晚于或等于原始驱动器。如果更换驱动器的固件较旧则ADC下载可能失败。
Version 4.02 Drive AOPs require user action to enable ADC.
This helps verify that the user understands ADC operation prior to turning it on. Note the following ADC operating status when using version 4.02 (or later) Drive AOPs: • When adding a new drive, ADC is disabled by default for any drive that supports ADC, such as PowerFlex 753 drives with firmware 7.001 or later, or PowerFlex 755 drives with firmware 4.001 or later. • When converting an earlier RSLogix 5000 project to a version 20.00 project that has been updated with version 4.02 (or later) Drive AOPs or when updating a project created with version 4.01 Drive AOPs, any ADC settings will be passed through as-is for drives that support ADC. For example: – If ADC was disabled for a drive in a previous project, it will remain disabled. – If ADC was enabled for a drive using version 4.01 Drive AOPs and that project was later updated to version 4.02 (or later) Drive AOPs, it will remain enabled.Keying for peripherals is managed via the respective Port Properties dialog box for each peripheral.
Electronic Keying for the embedded
EtherNet/IP adapter (only Port 13 on PowerFlex 755 drives) and DeviceLogix (Port 14) ports are “Disabled” by default. Both ports do not have individual firmware and are currently managed by the drive’s firmware (Port 0). If you set either of these to “Exact Match,” Firmware Supervisor will be unable to locate the upgrade files during setup. If the “Fault Drive Connection on Peripheral Error” checkbox is selected and there is a mismatch or failure while connecting to or configuring these two ports, the overall ADC process will fail and no I/O connection will be made to the drive. Electronic Keying for HIMs and serial converters (1203-SSS and 1203- USB) are disabled by default. These are typically temporary devices or used for monitoring purposes only and therefore “do not matter” if they are present or not. You still have the option to select these to other Keying selections if desired.
Compatible Module
This selection is the typical ADC selection when Firmware Supervisor is not used. A replacement drive (including peripherals) will need to have the same or higher firmware revision as the original. Since drives with newer firmware are required to be compatible with older firmware, this allows ADC to work without compatibility concerns. Note that if a Series change accompanies a Major firmware change, the replacement drive may or may not be “compatible” with respect to keying. Disabled When using ADC, this selection should generally not be used. This selection allows a replacement drive to have any different Major (X.xxx) and/or Minor (X.xxx) firmware revision. It is up to the user to provide a replacement that has a firmware revision later than or equal to the original drive. If a replacement drive with older firmware is used, the ADC download may fail.
公司主营产品图展示
产品优势
1：国外专业的供货渠道，具有价格优势
2：产品质量保证，让您售后无忧
3：全国快递包邮
4：一对一服务
公司主营范围简介
PLC可编程控制器模块，DCS卡件，ESD系统卡件，振动监测系统卡件，汽轮机控制系统模块，燃气发电机备件等，优势品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件、欧美进口模块。
产品广泛应用于冶金、石油天然气、玻璃制造业、铝业、石油化工、煤矿、造纸印刷、纺织印染、机械、电子制造、汽车制造、塑胶机械、电力、水利、水处理/环保、锅炉供暖、能源、输配电等等
