产品细节介绍
FIREYE 45UV5-1000自检火焰扫描器
使用以太网通信CPU模块内的Ethernet接口不能在直到配置了有效的IP地址。必要的以太网寻址信息必须在实际之前配置网络操作，或从意外更改中恢复以太网接口处的以太网寻址数据。使用其中一个以下方法用于初始分配IP地址：▪ 将串行终端连接到PAC系统RX7i。然后使用CHSOSW命令输入所需的IP地址。有关详细信息，请参阅PAC系统
TCP/IP Communications Station Manager手册，GFK-2225。
▪ 使用SetIP临时为模块分配IP地址以太网上的工具。有关详细信息，请参阅TCP/IP以太网PAC系统通信，GFK-2224。
▪ Ethernet接口自动获得临时IP
来自网络上BOOTP服务器的地址。有关详细信息，请参见PAC系统的TCP/IP以太网通信，GFK-2224。
一旦设置了临时IP地址，以太网可以通过网络访问接口（如机器编辑编程软件）。然后程序员应该用于为Ethernet接口配置正确的IP地址。
SRTP连接时更改IP地址打开可能会生成日志事件
打开与远程SRTP建立的SRTP服务器连接当RX7i的IP地址为更改（通常通过将新的硬件配置存储到RX7i）。
Series 90 SRTP客户端（“SRTP通道”）报告9690H或0190H状态；
SRTP连接可能会保持打开状态，直到由于客户端超时，连接被终止。不应更改AUP参数不应更改高级用户参数“wsnd_buf”由用户决定。更改此参数的值可能会导致LAN LED熄灭，Ethernet接口断开连接。重载可能会阻塞Station Manager，如PACSystems Station的TCP/IP通信中所述管理器手册，GFK-2225，重型EGD和/或SRTP负载可以阻止Station Manager操作。
EGD生产的一次延迟（和可能消耗量），如果超过24 SRTP服务器连接同时启动如果建立了24个以上的SRTP服务器连接同时，EGD生产可能会短暂延迟24号之后的连接通电。如果EGD消耗加速被禁用，则EGD消耗也将延迟。仅发生延迟第一次建立SRTP服务器连接时通电后的时间。第一个24 SRTP没有延迟服务器连接。
极大量EGD生产/消耗服务器可能导致EGD命令超时服务器设备上的EGD生产和/或消耗量非常大当另一个设备时，可能会导致EGD命令超时错误尝试向该服务器发送EGD命令。如果EGD命令必须抢占正常生产，您可以设置“gcmd_pri”高级用户参数为2（见GFK-2224，附录A）。EGD交换生产可能会延迟。
using Ethernet communications
The Ethernet Interface within the CPU module cannot operate on a network until a valid IP address is configured. The necessary Ethernet addressing information must be configured prior to actual network operation, or to recover from inadvertent changes to the Ethernet addressing data at the Ethernet Interface. Use one of the following methods to initially assign an IP address: ▪ Connect a serial terminal to the Station Manager port of the PACSystems RX7i. Then use the CHSOSW command to enter the desired IP address. For details, see the PACSystems TCP/IP Communications Station Manager manual, GFK-2225. ▪ Temporarily assign an IP address to the module using the SetIP tool over the Ethernet network. For details, see TCP/IP Ethernet Communications for PACSystems, GFK-2224. ▪ The Ethernet Interface automatically obtains a temporary IP Address from a BOOTP server on the network. For details, see TCP/IP Ethernet Communications for PACSystems, GFK-2224. Once a temporary IP address has been set up, the Ethernet Interface can be accessed over the network (as by the Machine Edition programming software). The programmer should then be used to configure the proper IP address for the Ethernet Interface. Changing IP address while SRTP connection open may generate log events Open SRTP Server connections established with a remote SRTP client are not terminated as expected when the RX7i’s IP address is changed (typically by storing a new HW Configuration to the RX7i). A Series 90 SRTP client (“SRTP channels”) reports either a 9690H or 0190H status; the SRTP connection may remain open until the connection is terminated as a result of a client timeout.
AUP parameter should not be changed
The Advanced User Parameter “wsnd_buf” should not be changed by the user. Changing the value of this parameter may cause the LAN LED to go out and the Ethernet Interface to drop connection. Heavy load can block Station Manager As explained in TCP/IP Communications for PACSystems Station Manager Manual, GFK-2225, a heavy EGD and/or SRTP load can block Station Manager operation. One-time delay of EGD Production (and possibly Consumption) if more than 24 SRTP Server Connections are started simultaneously If more than 24 SRTP Server connections are established simultaneously, EGD Production may be briefly delayed for each connection after the 24th when the connections are first made after power is applied. If EGD consume acceleration has been disabled, then EGD Consumption will also be delayed. The delay only occurs once when the SRTP Server connection is established for the first time after Powerup. No delay is experienced for the first 24 SRTP Server connections. Very heavy EGD production/consumption at server may cause EGD command timeouts Very heavy EGD production and/or consumption at a server device may cause EGD command timeout errors when another device attempts to send EGD commands to that server. If EGD commands must preempt normal production, you may set the “gcmd_pri” Advanced User Parameter to 2 (see GFK-2224, Appendix A). Note that by doing so, EGD exchange production may be delayed.
公司主营产品图展示
产品优势
1：国外专业的供货渠道，具有价格优势
2：产品质量保证，让您售后无忧
3：全国快递包邮
4：一对一服务
公司主营范围简介
PLC可编程控制器模块，DCS卡件，ESD系统卡件，振动监测系统卡件，汽轮机控制系统模块，燃气发电机备件等，优势品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件、欧美进口模块。
产品广泛应用于冶金、石油天然气、玻璃制造业、铝业、石油化工、煤矿、造纸印刷、纺织印染、机械、电子制造、汽车制造、塑胶机械、电力、水利、水处理/环保、锅炉供暖、能源、输配电等等
