产品详情内容介绍
B&R 5AP1130.156C-000控制触摸屏
工程操作程序根据操作的键盘功能按钮
可执行以下工程操作程序：
通道重置。
频道选择。
通道抑制。
报警配置和继电器测试。
催化桥电流调整。
零信号校准。
量程信号校准。
第一量程信号校准。
传感器信号监测。时钟/日历调整。
通道选择和复位由通道卡reset执行/选择按钮。见第6章第3节。
其余工程功能在控制卡之后执行已使用工程卡按钮控件选择。工程师的操作说明是指附加设施可用于设置和维护系统。
因为系统可以被这些功能改变或阻碍，它们只能工程部解锁工程卡时执行钥匙选择操作后，有四个控制按钮可用于根据需要操纵操作。这些是：a、 向上按钮，可用于提升选定的控制卡指示值。如果保持在操作位置显示将每0.5秒增加一个单位。
b、 向下按钮，可用于降低选定的控制卡指示值。如果保持在操作位置显示将每0.5秒减少一个单位。
c、 接受按钮，可用于接受所选控制卡显示的值并永久存储作为配置的一部分。将控制卡返回所选模式。
信道抑制按下工程卡INHIBIT（禁止）按钮可切换选定的控制卡通道抑制模式介于打开和关闭之间。
当抑制模式设置为打开时，从工程部本地卡或远程抑制输入
所选控制卡：
a、 通道抑制继电器（如已配置）启动。
b、 通道LED显示持续琥珀色以指示INHIBIT（抑制）。
c、 其余通道继电器锁定在非活动状态。
要选择禁止功能，请执行以下操作：
（1） 将工程钥匙插入工程卡前面板插座，并检查解锁指示灯是否亮起。
（2） 按住所需的控制卡重置/选择按钮约1.5秒，检查所选的控制卡通过显示选择来指示它已被选中偶像
（3） 使用工程卡（）和（）按钮选择所需通道。
（4） 按下INHIBIT（抑制）按钮以打开通道抑制模式/关闭。
拒绝按钮，可用于拒绝选定的控制卡显示值并返回到先前的设定值。将控制卡返回到所选模式。
ENGINEERING OPERATING ROUTINES
Depending upon the which keypad function push-button is operated, the following engineering operating routines may be carried out: Channel Reset. Channel Select. Channel Inhibit. Alarm Configuration and Relay Test. Catalytic Bridge Current Adjustment. Zero Signal Calibration. Span Signal Calibration. 1st Span Signal Calibration. Sensor Signal Monitoring. Clock/Calendar Adjustment. Channel select and reset are carried out by the channel card RESET/ SELECT push-button. See Chapter 6, Section 3. The remaining engineering functions are carried out after a control card has been selected using the Engineering Card push-button controls.The engineer's operating instructions refer to the additional facilities available to setup and maintain the system. Because the operation of the system can be altered or impeded by these functions, they can only be performed when the Engineering Card is unlocked by the Engineering Key.Once an operation has been selected, there are four control push-buttons which may be used to manipulate the operation as required. These are: a. The up push-button, which may be used to raise the selected control card indicted value. If held in the operated position, the display will be increased by one unit every 0.5 seconds. b. The down push-button, which may be used to lower the selected control card indicated value. If held in the operated position, the display will be decreased by one unit every 0.5 seconds. c. The accept push-button, which may be used to accept the selected control card displayed value and store this permanently as part of the configuration. Returns the control card to the selected mode.
CHANNEL INHIBIT
Pushing the Engineering Card INHIBIT push-button toggles the selected control card channel inhibit mode between on and off. When the inhibit mode is set to on, either locally from the Engineering Card or remotely by the Remote Inhibit input, the selected control card: a. channel inhibit relay, if configured, is actuated. b. channel LED shows continuous amber to indicate INHIBIT. c. remaining channel relays are locked in their non-active state. To select the inhibit function, proceed as follows: (1) Plug the Engineering Key into the Engineering Card front panel socket and check that the Unlocked LED ( ) is illuminated. (2) Push and hold the required control card RESET/SELECT pushbutton for approximately 1.5 seconds and check that the selected control card indicates it has been selected by displaying the select icon. (3) Use the Engineering Card ( ) and ( ) push-buttons to select the required channel. (4) Push the INHIBIT push-button to toggle the channels inhibit mode on/ off.
The reject push-button, which may be used to reject the selected control card displayed value and return to the previous set value. Returns the control card to the selected mode.
公司主营产品图展示
产品优势
1：国外专业的供货渠道，具有价格优势
2：产品质量保证，让您售后无忧
3：全国快递包邮
4：一对一服务
公司主营产品文字介绍
PLC可编程控制器模块，DCS卡件，ESD系统卡件，振动监测系统卡件，汽轮机控制系统模块，燃气发电机备件等，优势品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件、欧美进口模块。
产品广泛应用于冶金、石油天然气、玻璃制造业、铝业、石油化工、煤矿、造纸印刷、纺织印染、机械、电子制造、汽车制造、塑胶机械、电力、水利、水处理/环保、锅炉供暖、能源、输配电等等
