产品详情内容介绍
Kollmorgen 6SM56-S3000-G伺服自动化电机
这与上显示的错误代码消息ERxx有关LCD消息显示。如果出现多个错误
同时出现，代码最高的错误显示数字
卡片状态：指控制卡片操作的状态。
激活表示卡仍在处理信号从连接的传感器，如果是传感器
检测气体时，仍会激活任何配置的警报输出。
非活动意味着无法进行控制生成任何报警以响应传感器的卡检测气体。
故障信号：这是指对错误条件的响应。
是表示相应通道前面板故障LED和任何配置的故障继电器将运行。
否表示未给出故障指示。错误导致这些一般警告消息的条件属于次要性质，频道卡将继续运转然而，情况应该仍然是调查。
闩锁：这是指错误消息和相关故障信号。
是表示控制卡将继续显示错误消息，直到导致错误的条件已清除，并且已操作复位按钮。否表示错误消息将自动清除一旦导致错误消息的条件变明朗。
Conf表示闩锁/非闩锁状态为可使用工程接口软件进行配置。硬件故障如果出现以下情况，则显示硬件故障消息通道卡检测到其故障
操作或传感器输入故障。检查传感器连接。移除通道卡并将其插入兼容的工作通道并检查其操作
（此操作过程中可能会出现ER86-这是正常的）。如果卡片上仍显示故障，必须更换。如果卡是工作时，应更换传感器。显示低于范围故障消息当传感器信号读数小于通道内保持的预定电平配置数据。
通常这是由于传感器或传感器电缆安装打开电路将显示超范围故障信息
当传感器信号读数高于通道内保持的预定水平配置数据。通常，这是由于传感器或传感器电缆安装短环行或者，传感器可以检测到非常高的气体含量。
锁定信号超范围故障的复位条件只能在以下情况下执行检查传感器是否清洁（非目标气体）空气。这允许将卡移动到其他位置用于故障查找的插槽位置。这安装时也可能显示消息
新通道卡或安装备用卡替换可以清除消息将通道卡校准为新的插槽位置和连接的传感器。
根据报警配置，将通道卡移动到备用插槽可能会影响警报的生成。
报警操作应在卡已经移动和校准。
COMMISSIONING AND MAINTENANCE INSTRUCTIONS
Hardware Fault The hardware fault message is displayed if the channel card detects a fault in its operation or a fault with a sensor input. Check the sensor connections. Remove the channel card and insert it into a compatible working channel and check its operation (ER86 may appear during this operation - this is normal). If the card still indicates a fault, it must be replaced. If the card is working, the sensor should be replaced.The under range fault message is displayed when the sensor signal reading is less than the predetermined level held within the channel configuration data. Typically this is due to either the sensor or the sensor cable installation being open circuit
The over range fault message will appear when the sensor signal reading is above the predetermined level held within the channel configuration data. Typically, this is due to either the sensor or the sensor cable installation being short circuit. Alternatively, the sensor may be detecting a very high level of gas. The reset of a latched signal overrange fault condition should only be carried out after checking that the sensor is in clean (non target gas) air.
This allows cards to be moved to alternative slot locations for fault finding purposes. This message may also be displayed when fitting a new channel card or fitting a spare replacement. The message can be cleared by calibrating the channel card to the new slot location and connected sensor. Depending on the alarm configuration, moving channel cards to alternative slots may compromise the generation of alarms. The alarm operation should be checked after the card has been moved and calibrated.
ERROR CODES
This relates to the error code message ERxx displayed on the LCD message display. If more than one error is present simultaneously, the error with the highest code number is displayed Card Status: This refers to the condition of the control card operation. Active means that the card is still processing signals from the connected sensor and, in the event of the sensor detecting gas, will still activate any configured alarm outputs. Non active means that it is not possible for the control card to generate any alarms in response to the sensor detecting gas. Fault Signal: This refers to the indication of the fault condition in response to the error condition. Yes means that the appropriate channel front panel fault LED and any configured fault relay will be operated. No means that no fault indication is given. The error condition that causes these general warning messages is of a minor nature and the channel card will continue to operate. The condition should however still be investigated. Latch: This refers to the condition of the error message and the associated fault signal. Yes means that the control card will continue to display the error message until the condition causing the error has cleared and the reset push-button has been operated. No means that the error message will clear automatically once the condition causing the error message has cleared. Conf. means that the latch/non-latch condition is configurable using the Engineering Interface Software.
公司主营产品图展示
产品优势
1：国外专业的供货渠道，具有价格优势
2：产品质量保证，让您售后无忧
3：全国快递包邮
4：一对一服务
公司主营产品文字介绍
PLC可编程控制器模块，DCS卡件，ESD系统卡件，振动监测系统卡件，汽轮机控制系统模块，燃气发电机备件等，优势品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件、欧美进口模块。
产品广泛应用于冶金、石油天然气、玻璃制造业、铝业、石油化工、煤矿、造纸印刷、纺织印染、机械、电子制造、汽车制造、塑胶机械、电力、水利、水处理/环保、锅炉供暖、能源、输配电等等
