公司主营产品图展示
产品优势
1:国外专业的供货渠道,具有价格优势
2:产品质量保证,让您售后无忧
3:全国快递包邮
4:一对一服务
产品详情介绍
ETHERWAN 973G-1600RPSA-BK差动电压模块
中输入和输出地址的结构远程模块将解释二进制输入模块ICSI 08 D1这里是一个例子。总线主中央单元将输入信号读取为操作数。输入信号的完整地址有以下结构:一些其他模块可能有或多或少不同的地址设置,请参阅以下章节。上的建议模块地址CS31系统总线,带多个远程模块和中央单元连接为奴隶标准寻址的目的是–简化和示意设置CS31系统总线上的地址–简化诊断和故障排除。标准寻址确保不会出现地址重叠,即使对于更大的模块数据量。建议:为每个模块分配特定的模块地址模块/每个从属中央单元,即放弃双重赋值的可能性二进制和模拟模块的模块地址二进制远程模块的模块地址和中央单位:8、10、…、58、60(均为偶数),请参见也包括第A2.6章作为从设备连接的中央单元至CS31系统总线模拟远程模块的模块地址:0…5插入式底座ECZ上的8号地址开关始终设置为OFF(<7)A2.3模块的地址设置输入和输出模块作为从机连接至CS31系统总线
远程模块安装在插件底座上ECZ公司
此插件底座配有地址开关(DIL开关),用于设置模块地址。模块类型、模块地址和通道号导致使用的可变地址总线主中央单元。设置二进制模块的地址开关设置模拟情况下的地址开关模块如果使用模拟模块,其模块地址可以设置为0...5当中央单元07 KR 91/07 KT 92/07 KT93用作总线主机。07 KR 91/07 KT 92/07中的模拟表示KT 93是固定的。模拟模块必须提供值的格式,因此要设置为模拟表示b.对于模拟表示,参见模拟模块的一般说明(第2卷)。功能
Recommended module addresses on the
CS31 system bus with several remote
modules and central units connected as
slaves
The standard addressing has the purpose of
– simplifying and schematizing the setting of
addresses on the CS31 system bus
– simplifying diagnosis and troubleshooting.
The standard addressing makes sure that there will be no
address overlappings even for modules with a bigger
amount of data.
Recommendation:
Assign a specific module address for each
module/each slave central unit, that means the
giving up the possibility of double assignment of
module addresses by binary and analog modules
Module addresses for binary remote modules and
central units: 8, 10, ..., 58, 60 (all even numbers), see
also chapter A2.6 Central units connected as slaves
to the CS31 system bus
Module addresses for analog remote modules: 0...5
Address switch No. 8 on the plug-in base ECZ always
set to OFF (<7)
A2.3 Address setting for the modules
Input and output modules connected as slaves to the
CS31 system bus
The remote modules are mounted on the plug-in base
ECZ. This plug-in base is equipped with an address
switch (DIL switch) for setting the module address.
The combination of module type, module address and
channel number results in the variable address used by
the bus master central unit.
Setting the address switch for binary modules Setting the address switches in case of analog
modules
If analog modules are used, their module addresses can
be set to
0...5
when the central units 07 KR 91 / 07 KT 92 / 07 KT 93 are
used as bus master.
The analog representation in the 07 KR 91 / 07 KT 92 / 07
KT 93 is fixed. The analog modules have to supply their
values in a suitable form and therefore to be set to the
analog representation b. For the analog representation,
see the general description of the analog modules
(volume 2).
The function