公司主营产品图展示
产品优势
1:国外专业的供货渠道,具有价格优势
2:产品质量保证,让您售后无忧
3:全国快递包邮
产品详情介绍
DANAHER S20360-SRS伺服驱动器
这是进入待机模式前系统需要的电量暂停模式(最大功率关闭)。挂起模式关闭更多系统待机模式以外的设备。仅当节能时,此字段才可由用户编辑
字段设置为“自定义”。其他节能设置的只读值为:如上所述。当可编辑时,选项为关闭(默认)、5分钟、10分钟和10分钟,15分钟、20分钟、30分钟、40分钟和60分钟。
设备监控按ENTER键打开设备监控子菜单,用户可以在其中设置中断待机模式和挂起模式的设备。
启用给定IDE设备时,设备上的活动将中断待机模式、暂停模式和待机定时器。选项被禁用(默认),并且启用。注意:如果设备是CD-ROM,并且操作系统不断轮询CD-ROM(如Windows 95和Windows 98不支持),启用此设备上的监控可以防止系统从未进入暂停模式。
注:在XVME-660上,IDE辅助主机连接到紧凑型闪存适配器和IDE辅助从属设备未连接。
PCI总线监控当该字段启用时,PCI总线上的活动将中断待机模式,暂停模式和待机定时器。选项被禁用(默认),并且启用。
总线利用率阈值 总线百分比阈值
如果启用PCI总线监控设置,则会显示这些字段。因为PCI总线是始终处于活动状态,这些字段允许设置阈值。这些阈值设置指定必须存在多少PCI总线活动才能防止系统进入待机状态
模式或暂停模式。总线利用率阈值设置是数据数量在256时钟周期周期内检测的相位;默认设置为0。总线
百分比阈值是总线利用率阈值的时间百分比必须超过才能重新加载待机定时器,或中断待机,或暂停模式;默认设置为0。此菜单允许您指定设备的启动顺序。当你给装置通电时向上,它将尝试按列出的顺序从每个列出的设备启动。可移动固定驱动器是可以包含多个设备的设备组。这个系统将仅尝试从组中列出的第一个设备启动,然后继续通过引导顺序。
要更改组和设备的顺序,请使用上下箭头选择项目键,并使用<+>键(向上)和<–>键(向下)在列表中向上或向下移动。组内的设备只能在组内上下移动。
您可以在列出或不列出组中的设备之间切换,方法是选择分组并按ENTER键,然后按CTRL-ENTER键查看所有设备组。ATAPI可移动设备,如LS120或Iomega IDE Zip®驱动器,可能出现在任一组下。您可以通过以下方式在组之间移动这些设备:选择它们并按下<n>键。
This is the amount of the system needs to be in Standby mode before entering
Suspend Mode (maximum power shutdown). Suspend Mode turns off more system
devices than Standby Mode. This field is user-editable only when the Power Savings
field is set to Customized. Read-only values for other Power Savings settings are
given above. When editable, the choices are Off (default), 5 Minutes, 10 Minutes,
15 Minutes, 20 Minutes, 30 Minutes, 40 Minutes, and 60 Minutes.
Device Monitoring Press ENTER to open the Device Monitoring submenu, where the user can set certain
devices to interrupt Standby Mode and Suspend Mode.
When a given IDE device is Enabled, activity on the device will interrupt Standby
Mode, Suspend Mode, and the standby timer. The choices are Disabled (default) and
Enabled.
Note: If the device is a CD-ROM and the OS constantly polls the CD-ROM (as
Windows 95 and Windows 98 do), enabling monitoring on this device can prevent the
system from ever entering Suspend Mode.
Note: On the XVME-660, the IDE Secondary Master is wired to the Compact Flash
adapter, and the IDE Secondary Slave is not connected.
PCI Bus Monitoring When this field is Enabled, activity on the PCI bus will interrupt Standby Mode,
Suspend Mode, and the standby timer. The choices are Disabled (default) and
Enabled.
Bus Utilization Threshold
Bus Percentage Threshold
These fields appear if the PCI Bus Monitoring setting is Enabled. Since the PCI bus is
always active, these fields allow a threshold to be set. These threshold settings specify
how much PCI bus activity must exist to prevent the system from entering Standby
Mode or Suspend Mode. The Bus Utilization Threshold setting is the number of data
phases detected in a 256 clock cycle period; the default setting is 0. The Bus
Percentage Threshold is the percentage of time that the Bus Utilization Threshold
must be exceeded in order to reload the standby timer, or interrupt Standby or
Suspend Mode; the default setting is 0. This menu allows you to specify the boot order for the unit. When you power the unit
up, it will attempt to boot off of each listed device, in the order listed. The removable
and fixed drives are device groups that may contain more than one device. The
system will only attempt to boot off the first listed device in a group before it continues
through the boot order.
To change the order of groups and devices, select an item with the up and down arrow
keys and move it up or down the list with the <+> key (up) and the <–> key (down).
Devices inside of groups will only move up and down within the group.
You can toggle between listing or not listing the devices in a group by selecting the
group and pressing ENTER, and you can press CTRL-ENTER to view all devices in all
groups. ATAPI removable devices, such as LS120 or Iomega IDE Zip® drives, may
appear under either group. You can move these devices between the groups by
selecting them and pressing the <n> key.