ALSTOM 3BEE0226电源配套接口板
CPU板包含微处理器和RAM存储器、实时时钟、LED指示灯、Init按钮和CompactFlash界面
PM851A控制器的底板有两个RJ45以太网端口（CN1、CN2）用于连接控制网络，以及两个RJ45串行端口（COM3、COM4）。
请注意，PM851/PM851A仅限于一个以太网（CN1）端口，因此冗余以太网不可用。连载之一
端口（COM3）是带有调制解调器控制信号的RS-232C端口，而另一个端口（COM4）被隔离并用于配置工具的连接。
简单的DIN导轨连接/拆卸程序，使用独特的滑动和锁定机制。所有底板均配有唯一的以太网地址，为每个CPU提供硬件身份地址可以在以太网地址标签上找到连接到TP830基板。一般评论术语“DCS晶闸管功率转换器”是ABB基本直流转换器的通用名称。本学期可以在相关文档的许多部分找到。根据下面给出的简要描述描述了特定单元的特征。
DCS 500和DCS 500B的简要说明
DSC 500B单元范围是从DCS 500范围发展而来的增强。之间的差异控制板版本中有两个范围：用于DCS 500B装置范围的控制板为SDCS-CON-2型，与SDCS-CON-1型有几点不同（见下表）。
DCP 500和DCP 500B的简要说明在DCP 500单元中，这改变了其视觉外观、安装尺寸和电源部分之间的接口以及电子设备。DCP装置在功能上与DCS装置兼容，因为电子设备（电源组件、控制板和选项和/或控制）是相同的。DCP 500B单元范围是一个增强
从DCP 500系列开发而来，两个系列之间的差异在于控制板：用于DCP 500B装置范围的控制板为SDCS-CON-2型，与SDCSCON-1型有几点不同（见下表）。DCF 500B简介
软件版本为21.232或更高版本时，DCS 500B具有“三相励磁机模式”。DCF 500B是基于可编程DCS 500B软件和SDCS-CON-2控制板的三相励磁机。
修改了接口板引脚1x/引脚2x；-需要过电压保护单元DCF 505/506。
DCS 600简介
DCS 600变频器系列基于为DCS 500B型开发的硬件。
使用SDCS_AMC_DC板代替COM-x板。PC工具将连接到那里，以及如果APC用作PLC，则为APC（应用程序控制器）。如果使用不同的PLC，则使用单独的适配器需要模块。它们也必须连接到AMC-DC板。软件代码总是开始S15.xxx适用于多驱动，S18.xxx用于起重机驱动。
The CPU board contains the microprocessor and RAM memory, a realtime clock, LED indicators, INITpush button, and a CompactFlash
interface.
The base plate of the PM851A controller has two RJ45 Ethernet ports
(CN1, CN2) for connection to the Control Network, and two RJ45
serial ports (COM3, COM4).
Note that a PM851/PM851A is restricted to one Ethernet(CN1)
port, thus redundant Ethernetis not available. One of the serial
ports (COM3) is an RS-232C portwith modemcontrol signals,
whereas the other port(COM4) is isolated and used for the
connection of a configuration tool.
Simple DIN rail attachment / detachment procedures, using the
unique slide & lock mechanism. All base plates are providedwith a
unique Ethernet address which provides every CPUwith a hardware
identity. The address can be found on the Ethernet address label
attached to the TP830 base plate.General remarks
The term “DCS thyristor power converter” is a general designation for basic DC converters from ABB. This term
can be found in many parts of the relevant documentation. The precise product name in accordance with the
brief descriptions given below characterizes a specific unit.
Brief description of DCS 500 and DCS 500B
The DSC 500B unit range is an enhancement developed from the DCS 500 range. The difference between the
two ranges lies in the version of the control board: the control board used for the DCS 500B unit range is the
SDCS-CON-2 type, which is different from the SDCS-CON-1 type in several points (see the table below).
Brief description of DCP 500 and DCP 500B
In the DCP 500 unit, the electronics of the DCS 500 unit have been equipped with a different power section,
which changes its visual appearance, its installation dimensions and the interface between the power section
and the electronics. The DCP unit is functionally compatible with the DCS unit, since the electronics (power
pack, control board and options and/or control) are identical. The DCP 500B unit range is an enhancement
developed from the DCP 500 range, with the difference between the two ranges lying in the control board: the
control board used for the DCP 500B unit range is the SDCS-CON-2 type, which is different from the SDCSCON-1 type in several points (see the table below).Brief description of DCF 500B
With software release 21.232 or higher DCS 500B has a '3-phase field exciter mode'. A DCF 500B is a threephase field exciter based on the programmable DCS 500B software and the SDCS-CON-2 control board.
The interface boards PIN-1x/PIN-2x are modified; - an overvoltage protection unit DCF 505/506 is required.
Brief description of DCS 600
The DCS 600 converter family is based on the hardware developed for the DCS 500B type.
Instead of a COM-x board, the SDCS_AMC_DC board is used. PC tools will be connected there, as well as
the APC (Application controller), if the APC is used as a PLC. If a different PLC is used, separate adapter
modules are needed. They must be connected to the AMC-DC board, too. The software code always begins
with S15.xxx for MultiDrive or S18.xxx for Crane drives.
