CSI3120振动变送器
恢复出厂变量参数：要恢复原始出厂变量参数，请拉在“配置”菜单下，选择“电机”，然后选择电机族和电机型号。点击“至驱动”按钮将变量参数发送到RAM和“RAM/E2
“保存”按钮保存到EEPROM。
恢复自定义变量参数：此过程假设您保存了自定义变量
参数设置为.SSV文件，如上所述。要恢复自定义参数，请下拉编辑
菜单中，选择备份变量，然后单击“打开”。突出显示要导入变量的自定义.SSV文件
参数输入编辑器。单击“Xmit”将变量参数发送到驱动器。
终端模式
使用MOTIONLINK终端模式（或任何其他“哑”主机）直接监控或修改
变量设置和命令驱动器。这种方法仅适用于带有Windows的PC操作系统不可用和/或您熟悉变量和命令集。
每个变量和命令都引用其语法和参数定义。变量和命令按字母顺序分组，便于查找，并在本手册末尾找到。确信在开始之前，请查看此信息。
初始启动
大多数驱动器出厂时已为特定电机配置。你可以证实这一点
通过施加逻辑电源并监控状态显示。工厂配置的驱动器通过
通电顺序：在稳定到指示
操作模式。如果驱动器未配置特定电机，显示屏将闪烁负号符号“-”，表示必须输入驱动器、电机和应用程序变量参数。其余的本节的介绍了设置未配置驱动器的过程。
向驱动器通电时必须小心。工厂配置为：通电后启用。
验证硬件远程启用
（远程）启用开关被禁用。
通电后，伺服星执行一系列自检。如果状态显示点亮，则实数，则未发现错误，EEPROM已加载其可变参数（或已加载在EEPROM数据无效的情况下具有默认值）输入RAM。I/O上的远程启用开关
连接器（C3）现在可以通电，从而启用伺服回路。驱动启用逻辑基于以下变量开关和标志：
激活：这是指示驱动器启用/禁用状态的总体就绪标志。如果高（1） ，驱动器已启用，电机正在通电。下式必须为真才能使活动变高：活动=（就绪）和（远程）
其中就绪=（DRIVEOK）和（SWEN）
就绪：表示驱动器无故障且已准备好硬件启用的标志。
DRIVEOK（驱动器正常）：开关指示驱动器故障的状态。
SWEN：开关指示软件启用状态（EN或DIS）。
远程：开关指示C3连接器上硬件远程启用线路的状态。
Restoring Factory Variable Parameters: To restore the original factory variable parameters, pull down the Configure menu, select Motor, and select the motor family and motor model. Click the “To Drive” button to send the variable parameters to RAM and the “RAM/E2 SAVE” button to save to EEPROM. Restoring Custom Variable Parameters: This process assumes that you saved the custom variable parameters to a .SSV file, as described above. To restore the custom parameters, pull down the Edit menu, select Backup Variables, and click on “Open”. Highlight the custom .SSV file to import variable parameters into editor. Click “Xmit” to send variable parameters to drive. Terminal Mode Use the MOTIONLINK Terminal Mode (or any other “dumb” host) to directly monitor or modify the variable set and command the drive. This approach should only be taken when a PC with a Windows operating system is not available and/or you are well-versed with the variable and command set. Each variable and command are referenced for its syntax and parameter definition. The variables and commands are grouped alphabetically for easy look-up and are found at the end of this manual. Be sure you review this information before you begin. Initial Startup Most drives are shipped from the factory already configured for a particular motor. You can verify this by applying logic power and monitoring the Status Display. A factory-configured drive goes through a power-up sequence flashing all segments of the display before settling out to a number indicating the mode of operation. If the drive is not configured with a particular motor, the display will flash a minus sign "-", indicating that you must enter drive, motor, and application variable parameters. The remainder of this section describes the process of setting up a non-configured drive. Caution must be taken when applying power to the drive. It is factory-configured to enable upon application of power. Verify that the hardware Remote Enable (REMOTE) enable switch is disabled. Upon powering up, the SERVOSTAR performs a series of self-tests. If the Status Display illuminates a solid number, then no errors were found and the EEPROM has loaded its variable parameters (or loaded with default values in case of invalid EEPROM data) into RAM. The Remote Enable switch on the I/O connector (C3) may now be energized, thus enabling the servo loops.
