SC540控制卡件
短期调试指南
•关闭DCS 400电子电源。
•将现场总线适配器安装在安装轨道上。
•将适配器连接到电源（X8）。
•将光缆从适配器连接到DCS 400（V800）。
•将现场总线电缆连接至现场总线适配器。
•打开DCS 400电子电源。
•等待约10秒。在这段时间内，将在现场总线适配器和DCS 400。大多数现场总线该过程后，现场总线适配器自动预定义参数。
•设置现场总线第1部分（8.01）（模块类型）=现场总线。
•设置用户特定参数。有关详细说明，请参阅以下说明现场总线适配器。
•等待10秒。
•关闭并再次打开电子设备电源
提供，以便重新初始化用户特定参数设置，已更改为包括串行通信。
通信参数Cmd位置（2.02）
通信故障模式（2.07）和通信故障时间（2.08）需要手动设置，以便沟通和监督。请参阅本文档前面关于通信参数的章节。所使用的半导体熔断器是叶片熔断器。这个下表列出了相关数据。保险丝这种结构需要特殊的保险丝座。OFAX和OFAS型系列保险丝座可用于：这个目的。三相滤波器EMC电源滤波器是必要的，以便：如果是功率转换器，则应符合EN 50 081
将在公共低压下运行
例如，在欧洲，电网电压为400 V在相位之间。这种网格具有接地中性导线。对于在这些情况下，ABB提供其三相500V和25A…1000A电源滤波器。
在工厂内部的本地线路上，他们没有供应敏感电子产品。因此转换器不需要EMC滤波器。
在第5.2章中，按照使用EMC，介绍了主题EMC过滤器。电枢电感的测量值高于的最大值
参数臂电感（3.12）。
无法通过Arm自动调谐进行设置。手动将其设置为正确的值或达到最大值。
设置参数Arm Cur Nom（1.01）
临时至当前值的160%
并再次开始自动调谐。之后将参数1.01设置回上一个价值
Short Commissioning Guide
• Switch Off DCS 400 electronics power supply.
• Mount fieldbus adapter on mounting rail.
• Connect adapter to power supply (X8).
• Connect optical cables from adapter to DCS 400(V800).
• Connect fieldbus cable to fieldbus adapter.
• Switch On DCS 400 electronics power supply.
• Wait approximately 10 s.
During this time an initialization is done between
fieldbus adapter and DCS 400. Most of fieldbus
parameter are pre-defined by the fieldbus adapter automatically after that procedure.
• Set Fieldbus Par 1 (8.01) (Module Type) = Fieldbus.
• Set user specific parameters. For detailed description, refer to the description which is following the fieldbus adapaters.
• Wait 10 s.
• Switch Off and On again the electronics power
supply, in order to re-initialize the user specific
parameter settings, which have been changed to
include the serial communications.
The communication parameters Cmd Location(2.02),
Comm Fault Mode (2.07) and Comm Fault Time
(2.08) need to be set manually, for the purpose of
communication supervision. See chapter about communication parameters earlier in this document.The semiconductor fuses used are blade fuses. The
relevant data are listed in the table below. The fuses'
construction requires special fuse holders. Fuse holder of the OFAX and OFAS type series are available for this purpose.Three-phase filters
EMC mains filters are necessary so as to comply with EN 50 081 if a power converter
is to be operated at a public low-voltage
grid, in Europe, for example, with 400 V
between the phases. Grids of this kind
have an earthed neutral conductor. For
these cases, ABB offers its three-phase
mains filters for 500 V and 25 A ... 1000 A.
On local lines inside factories they do not
supply sensitive electronics. Therefore
converters do not need EMC filters.
In chapter 5.2 Installation in accordance
with EMC the topic EMC filter is described.Measurement Armature Inductance
value is higher than maximum value of
parameter Arm Inductance (3.12).
Not possible to set it by Arm Autotuning. Set it manually to the right value
or to maximum value.
Set parameter Arm Cur Nom (1.01)
temporary to 160% of current value
and start autotuning again. Afterwards
set parameter 1.01 back to previous value.
