8910-PS-DC燃机控制器
手动调试a的简要说明DCS400通过控制面板。
如果面板调试向导具有：失败。
适用于以下图表中的软件版本108.0及更高版本
根据速度的不同调试步骤给出了测量结果。具体信息有关参数和面板处理，请参阅
相应章节。DCS400适用于230…500V的主电源没有任何参数设置。监视软件正在以一种新的方式工作。这个
最小允许电源电压计算如下：电枢标称电压参数的平均值
(1.02). 如果电网电压实际值低于计算电压或参数，则电枢电压太高与标称电源电压相关的高驱动
没有开始。既不驾驶，也不自动调谐
正在工作。最小允许电源电压为：按公式计算
Umains>=Uarm/（1,35 x cosα）
4-Q:Umains>=Uarm/（1,35 x 0866）
2-Q:Umains>=Uarm/（1,35 x 0966）
救济根据以下内容设置参数Arm Volt Nom（1.02）：
DCS400手动和/或设置参数净欠压
跳闸（1.10）至较低（！）价值参数网欠压跳闸（1.10）与标称电源无关
电压此参数定义了额外的安全性超出（计算）最小允许值的裕度
电源电压。较高的（位置）值使监测更敏感、更低（也是负）值增加监测的容忍度。
另请参阅手册章节：
2.2表2.2/4，推荐的直流电压…
4.5.1监控电源电压
6.4故障排除（故障、报警、诊断）
n驱动器未准备好运行
•A09紧急停止后：在操作面板DCS400PAN保持均匀
如果打开并运行，则命令将关闭和打开再一次零速Lev（5.15）=0rpm，分别过低。必须大于0rpm。
•正常运行期间：绿色和红色LED在操作面板上，显示DCS400PAN
驱动器的实际状态。更多信息请参阅第6.4.4章“面板的重要性”LED的。接通电源后将检查频率和磁场电流。在10秒内，该检查必须成功，并且驱动逻辑必须准备好运行。
否则将发生故障。n等待静止诊断消息
该诊断消息可以在调试向导期间在任何自动调谐功能（字段，电枢、速度和磁通）和速度测量
调整（电动势、模拟转速表和编码器）
零速度Lev（5.15）=0，分别过低。
必须大于0rpm。
Short description for manual commissioning a
DCS400 via control panel.
Follow this guide if panel commissioning wizard has
failed.
Valid for software version 108.0 and higher In the following charts the main structure of the
different commissioning steps refering to the speed
measurement are given. For the specific information
related to the parameters and panel handling see the
corresponding chapters.DCS400 is suitable for main supply of 230…500V
without any parameter settings. To monitor the main
supply the software is working in a new way. The
smallest allowable mains voltage is calculated by
means of parameter Armature Voltage Nominal
(1.02). If mains voltage actual is lower than calculated voltage or parameter armature voltage is too
high related to nominal mains voltage the drive
doesn’t start. Neither drive ON nor the autotunings
are working. The smallest allowable mains voltage is
calculated by formula
Umains >= Uarm / (1,35 x cos alpha)
4-Q: Umains >= Uarm / (1,35 x 0,866)
2-Q: Umains >= Uarm / (1,35 x 0,966)
Remedy
Set parameter Arm Volt Nom (1.02) in accordance to
DCS400 Manual and / or set parameter Net Underv
Trip (1.10) to a lower (!) value. Parameter Net
Underv Trip (1.10) is not related to nominal mains
voltage! This parameter defines an additional safety
margin over the (calculated) minimum allowable
mains voltage. Higher (pos.) values makes the
monitoring more sensitive, lower (also neg.) values
increase the tolerance of monitoring.
Refer also manual chapter:
2.2 table 2.2/4, Recommended DC voltage …
4.5.1 Monitoring the Mains Voltage
6.4 Troubleshooting (Faults, Alarms, Diagnostics)
n Drive not ready for operation
• After A09-Emergency Stop: Green LED at the
operating panel DCS400PAN is keeping off even
if ON and RUN command is switching off and on
again. Zero Speed Lev (5.15) = 0rpm , respectively too low. Has to be greater than 0rpm.
• During normal operation: Green and red LED‘s
at the operating panel DCS400PAN are showing
the actual state of the drive. For more information
please refer chapter 6.4.4 Significance of panel
LED’s. After ON command the mains supply and
frequency and field current will be checked.
Within 10 sec this check must be successful and
the drive logic has to be ready for operation.
Otherwise a fault will occur.
n Wait For Standstill diagnosis message
This diagnosis message can occur during Commissioning Wizard at any autotuning function (Field,
Armature, Speed and Flux) and Speed Measurement
Adjustment (EMF , Analog Tacho and Encoder) if
Zero Speed Lev (5.15) = 0 , respectively too low.
Has to be greater than 0rpm.
