Rexroth VTS0234-47/AP025驱动卡件
在可以从面板控制驱动器之前，首先控制面板必须获得控制权。小组的能力：控制：驱动由面板锁定功能决定，该功能：可通过菜单选择和LOC/REM访问面板上提供的钥匙。面板锁定模式必须设置为解锁或无par写入，因为所有其他条目将阻止面板控制驱动器。使用LOC/REM键
以实际将控制转移到面板。然后通过以下方式发出信号：状态行中的LOC状态指示。按键
这将再次导致面板放弃对驱动，状态行中的LOC指示将消失。
实际值显示
在面板显示的第一行中，选择的实际值
使用参数，面板动作1（6.16）至面板动作3（6.18）为：表明。所需的实际值必须用这些参数预先定义。控制驱动器时在面板中，实际值不断更新。
参考显示
在该行中，通过向上/向下设置速度参考显示键。
状态显示
状态行中的LOC表示驱动器正在被控制来自面板。
RUN in der状态行表示驱动器已打开，并且启用。
激活引用
参考值的任何修改必须由以下人员发起：
按下回车键，将生成参考值
以下划线显示。所需的参考值如下：使用向上/向下键设置。更改参考仅当参考值显示为下划线。使用向上/向下键，您可以设置任何速度
0 rpm和最大转速之间的参考值，定义如下：参数最大速度（1.06）。
驾驶和启动，驾驶和停止
警告：必须采取适当的安全预防措施在启动驱动器之前。
此键的功能取决于当前驱动器状态。
如果驱动器处于关闭状态，按下此键将打开线路接触器并启用控制器。驱动器将根据预设斜坡时间（5.09）加速至选择的速度参考。
如果驱动器处于打开状态，按下此键将停止驱动器。
然后，驱动器将根据预设停止减速
模式（2.03）和斜坡时间（5.10，如果激活），并将切换离线接触器。
改变参考极性
参考中指示的速度参考极性
按此键可更改显示。电机将首先减速然后加速-仅在第四季度应用中-在相反的方向。
重置（故障确认）
转换器检测到的所有故障可通过以下方式进行重置：如果相关故障不存在，则按下此键不再活跃。
Before the drive can be controlled from the panel, the panel first
must be given permission to take control. The panel’s ability to
control the drive is determined by the Panel Lock function which
can be accessed through menu selection and by the LOC/REM
key provided on the panel. The Panel Lock mode must be set to
unlocked or no par write, since all other entries will prevent the
panel from taking control of the drive. The LOC/REM key is used
to actually transfer control to the panel. This is then signaled by
the LOC status indication in the status line. Pressing the key
once again will cause the panel to give up its command of the
drive, and the LOC indication in the status line will disappear.
Actual value display
In the first line of the panel display, the actual values selected
with the parameters Panel Act 1 (6.16) to Panel Act 3 (6.18) are
indicated. The desired actual values have to be defined beforehand with these parameters. When the drive is being controlled
from the panel, the actual values are continually updated.
Reference display
In this line, the speed reference set by means of the UP/DOWN
keys is displayed.
Status display
LOC in the status line indicates that the drive is being controlled
from the panel.
RUN in der status line indicates that the drive is switched on and
enabled.
Activate reference
Any modification of a reference value has to be initiated by
pressing the ENTER key, which will result in the reference value
displayed being underlined. The desired reference value is then
set using the UP/DOWN keys.Change reference
A reference value can be changed only when it is displayed with
an underline. Using the UP/DOWN keys, you can set any speed
reference between 0 rpm and the maximum speed defined with
the parameter Max Speed (1.06).
Drive ON and START, Drive OFF and STOP
CAUTION: Appropriate safety precautions must be taken
before starting the drive.
The function of this key is dependent on the current drive status.
If the drive is in the OFF state, pressing this key will switch ON
the line contactor and enable the controller. The drive will the
accelerate in accordance with the preset ramp time (5.09) up to
the selected speed reference.
If the drive is in the ON state, pressing this key will stop the drive.
The drive will then decelerate in accordance with the preset stop
mode (2.03) and ramp time (5.10, if activated) and will switch
OFF the line contactor.
Change reference polarity
The polarity of the speed reference indicated in the reference
display can be changed by pressing this key. The motor will first
decelerate and then accelerate - only in 4Q applications - in the
reverse direction.
Reset (Fault acknowledgement)
All faults detected by the converter can be reset by simply
pressing this key, provided that the faults concerned are no
longer active.
