SYHNC100-NIB-2X/W-24-P-D-E23-A012驱动模块
INDRAMAT的电子驱动组件配备有：广泛的安全功能，并在技术上防止过载尽最大可能。
应注意以下指南，以防止不当处理：开机前检查：
–仅在控制器输入端连接相应的电压在数据表和连接计划中列出！
–不要将输出连接到外部电压！
–检查以确定24V和+15V输出端子没有错误连接！检查低电压5、+15、-15和24伏是否已与电源电位安全隔离，未从外部与或接触
•电力电缆，
•链路电路电缆（L+、L-）或
•电机电源电缆的连接！
它们必须彼此充分绝缘！
–当使用外部电压检查控制柜接线时确保没有无效电压可以到达电子设备的端子组件！
为了确保安全，在检查之前，先夹紧连接！
–高压检查：
INDRAMAT的电子驱动部件已经过电压检查
根据VDE 0160进行详细测试。检查工业机械电气设备的高压
控制柜接线，拆除或夹紧所有电子连接，以避免损坏电子部件（适用于VDE 0113，EN 60204）！
以下INDRAMAT产品是电子设备的一部分：TVM、TVD、TDM、TWM、TFM、TBM、TCM、KDV、TVR、KDR、KVR、KDS、KDW、KDA、KDF、RAC、DSC3以及反馈和MAC电机和2AD的编码器电子设备。
静电负载危害电子元件。那些身体可与连接端子、部件和适配器板必须通过接地进行放电。
–在触摸之前，通过触摸导电的，接地物体（如普通接地金属）。
–焊接时，将烙铁接地！
–将正在使用的零件和工具放置在导电的接地系统上
表面
诸如适配器板或编程模块的危险部件，只能在导电包装中储存和运输。
INDRAMAT’s electronic drive components have been equipped with
extensive safety features and technically secured against overloads to
the greatest extent possible.
The following guidelines should be noted to prevent improper handling:
Check before switching on:
– Only connect voltages at the controller inputs that correspond to those
listed in the datasheets and connection plans!
– Do not connect outputs to an external voltage!
– Check to ascertain that the 24V and the +15V output terminals have not
mistakenly been connected! Check whether the low voltages, 5, +15, -15 and 24 volts, have been
securely separated from the mains potential, have not been externally
connected with or come into contact with the
• power cables,
• link circuit cables (L+, L-), or,
• connections to the motor power cables!
They must be sufficiently insulated against each other!
– When checking the control cabinet wiring with outside voltages, make
sure that no invalid voltages can reach the terminals of the electronic
components!
Just to be sure, clamp the connections off before checking!
– High-voltage checks:
INDRAMAT’s electronic drive components have been voltage-checked
in detailled tests in accordance with VDE 0160. When checking the
high-voltage of the electrical devices of industrial machinery and the
control cabinet wiring, remove or clamp off all the electronic connections to avoid damaging the electronic components (applicable acc. to
VDE 0113, EN 60204)!
The following INDRAMAT products are a part of the electronic equipment: TVM, TVD, TDM, TWM, TFM, TBM, TCM, KDV, TVR, KDR,
KVR, KDS, KDW, KDA, KDF, RAC, DSC3 as well as the feedback and
encoder electronics of the MAC motors and 2AD.
Electrostatic loads endanger electronic components. Those bodies that
can come into contact with connecting terminals, components and
adaptor boards, must be discharged by grounding them.
– Before touching, discharge your own body by touching a conductive,
grounded object (e.g., plain grounded metal).
– When soldering, ground the soldering iron!
– Place the parts and tools being used on a conductive, grounded
surface.
Endangered parts, such as adaptor boards or programming modules,
should only be stored and transported in conductive packaging.
