主营产品
PLC可编程控制器模块，DCS卡件，ESD系统卡件，振动监测系统卡件，汽轮机控制系统模块，燃气发电机备件等，优势品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各种进口工业零部件
产品广泛应用于冶金、石油天然气、玻璃制造业、铝业、石油化工、煤矿、造纸印刷、纺织印染、机械、电子制造、汽车制造、塑胶机械、电力、水利、水处理/环保、锅炉供暖、能源、输配电等等
HONEYWELL ACX633自动化卡件
调试：打开驱动器的控制电压后，仅显示两个点最初会亮起。
初始化成功后，如果没有错误或警告挂起，则显示为bb。
如果AS继电器已连接，且电源装置的电源电压则驱动控制器读取Ab。
控制应用启用后，驱动控制器读取AF。
警告：只要应用警告，驱动器就会在H1中显示诊断显示，但没有其他响应。
例外：如果应用了电源部分的警告超温超过30秒，并且在试验过程中没有来自控制装置的反应
此时，电源部分的错误信息为并开始断电。
错误：如果发生错误，则将其存储并显示在H1显示中。
错误和状态显示由/SH2的负侧翼清除来自控制。只有在控制关闭且然后再次。
如果警告和错误同时挂起，则错误具有优先级并显示。
如果同时发生多个错误，则只有第一个错误显示。
供应和附加组件：可以读取电源和其他部件的详细诊断在相关单位关闭。
带供应装置的驱动器上既没有读数也没有反应警告，例如散热器超温预警。
如果HVR供电装置发出反馈过载警告驱动控制器的电源端级被短时间锁定。这个驱动器不显示此信息，也不向控制器发送信号。
驱动控制器的驱动启用在电源单元中被移除发出错误信号。还生成连接控件的消息。
连接错误：如果控制器将两个PWM连接器连接到一个驱动轴，则产生错误并显示诊断88。
Commissioning:
After switching on the control voltage of the drive, only the two display
points will initially light up.
After the initialization has been successful, and if no error or warning are
pending, then the display reads bb.
If the AS relay is connected and the power voltage at the supply unit has
been brought into load, then the drive controllers read Ab.
After the control has applied the enable, then the drive controller reads
AF.
Warnings:
As long as a warning is applied, the drive displays the diagnoses in the H1
display, but no other response ensues.
Exception: If the warning overtemperature in power section is applied
longer than 30 seconds and there is no reaction from the control during
this time, then the error message overtemperature in power section is
generated and a power shutdown is started.
Error:
If an error occurs, then it is stored and shown in the H1 display.
The error and status display are cleared by a negative flanke from /SH2
from the control. This is only possible if the control is switched off and
then on again.
If a warning and an error are both pending simultaneously, then the error
has priority and is displayed.
If more than one error occurs at the same time, then only the first is
displayed.
Supply and additional components:
Detailed diagnoses of the supply and additional components can be read
off at the relevant units.
There is neither a reading nor a reaction at the drive with supply unit
warnings, e.g., heatsink overtemperature prewarning.
In the case of a feedback overload warning from HVR supply units, the
power end stages of the drive controller are locked for a short time. The
drive does not display this nor does it signal this to the control.
The drive enable of the drive controller is removed is the supply unit
signals an error. A message for the connected control is also generated.
Connectionerror:
If the control connects two PWM connectors to one drive axis, then an
error is generated and diagnosis 88 displayed.
