P0926TL输入输出卡件
报警的默认优先级为3（参见第3.2节中的报警块），这意味着必须确认报警以清除闪烁。报警也可配置为自清除。尝试使用将报警优先级更改为4第2节中的配置路线图或以下步骤：
1.按回车/退出配置。应显示循环。
2.按两次“向下”键，直到显示屏上出现“视图”。
3.按向右箭头按钮3次或转动脉冲发生器旋钮，直到显示屏上出现编辑FB。
4.按下“下一步”。将显示A/M。
5.按向右箭头按钮3次或转动脉冲发生器旋钮，直到显示器上出现报警。
6.按下“下一步”以显示RG PTR
7.按下向右箭头按钮或转动脉冲发生器旋钮，直到显示器上出现A1 Previor。
8.按下步进键，在数字显示器上显示3。
9.要将报警1的优先级从3更改为4，请旋转脉冲发生器旋钮，直到数字显示屏上出现4。
10.按存储保存配置更改。
11.按ENTER/EXIT CONF返回正常操作。10.1.7标签
按下标记按钮。请注意，Loop01.*=P、S、V、X或Y）将在屏幕上滚动。为了改变标签，
请参阅第2节中的配置路线图或以下说明：
请注意，虽然标记有12个字符可用，但建议将循环名称限制为6个字符
以便在正常操作期间显示完整的标签名称。另外6个字符可以是：通过滚动标签来显示。正常操作期间显示的字母数字的最后两位数字为：
用于标识当前显示的变量P、S、V、X或Y。
1.按回车/退出配置。将显示循环。
2.按两次“向下”键，直到屏幕上出现“视图”。
3.按下向右箭头按钮或旋转脉冲发生器旋钮，直到显示屏上出现编辑标签。
4.按下“下一步”。LOOP01将以1位数字闪烁出现在显示器上。使用脉冲发生器旋钮：
更改闪烁字符的值，然后按存储保存更改。使用箭头按钮移动到另一个角色。尝试将标签更改为TC101。
5.按ENTER/EXIT CONF返回正常操作模式。
6.按TAG可查看超过6个字符的标签名称。
10.1.8快速
在正常操作模式下，快速按钮可用于单步通过任何
启用此功能的功能块。在FCO101中，SETPT功能块具有快速设置功能
默认启用。按下快速按钮，注意您可以滚动浏览以下设定点功能：
斜坡接通/断开、斜坡速率、目标设定点和加电设定点。渐变功能可以使用
斜坡时间或斜坡速率。默认情况下，使用率设置为“是”（参见第节中的“设置PT功能块详细信息3.2).
Alarms have a default priority of 3 (see Alarm block in Section 3.2), meaning that the alarms must be acknowledged
to clear the flashing. Alarms may also be configured as self clearing. Try changing the alarm priority to 4 using the
Configuration Road Map in Section 2 or the following steps:
1. Press ENTER/EXIT CONF. LOOP should be displayed.
2. Press STEP DOWN twice until VIEW appears on the display.
3. Press the right arrow button 3 times or turn the pulser knob until EDIT FB appears on the display.
4. Press STEP DOWN. A/M will be displayed.
5. Press the right arrow button 3 times or the turn pulser knob until ALARM appears on the display.
6. Press STEP DOWN to display RG PTR
7. Press the right arrow button or turn the pulser knob until A1 PRIOR appears on the display.
8. Press STEP DOWN to display 3 on the numeric display.
9. To change the priority of alarm 1 from 3 to 4, rotate the pulser knob until 4 appears on the numeric display.
10. Press STORE to save the configuration change.
11. Press ENTER/EXIT CONF to return to normal operation. 10.1.7 TAG
Press the TAG button. Note that Loop01.* (*= P, S, V, X or Y) will scroll across the screen. To change the tag,
refer to the Configuration Road Map in Section 2 or the following instructions:
Note that although 12 characters are available for the tag, it is suggested that loop names be limited to 6 characters
so that the complete tag name will be displayed during normal operation. The additional 6 characters can be
displayed by scrolling the tag. The last two digits of the alphanumeric displayed during normal operation will be
used to identify the variable currently being displayed, P, S, V, X or Y.
1. Press ENTER/EXIT CONF. LOOP will be displayed.
2. Press STEP DOWN twice until VIEW appears on display.
3. Press the right arrow button or the turn pulser knob until EDIT TAG appears on the display.
4. Press STEP DOWN. LOOP01 will appear on the display with the 1 digit flashing. Use the pulser knob to
change the value of the flashing character and press store to save the change. Use the arrow buttons to move to
another character. Try changing the TAG to TC101.
5. Press ENTER/EXIT CONF to return to normal operation mode.
6. Press TAG to view tag names longer than 6 characters.
10.1.8 QUICK
When in normal operation mode the QUICK button can be used to step through the QUICK SET parameters of any
function block which has this feature enabled. In FCO101, the SETPT function block has the QUICK SET feature
enabled as a default. Press the QUICK button and note that you can scroll through the following Setpoint features:
RAMP ON/OFF, Ramp RATE, TARGET setpoint, and POWER UP SETPOINT. The ramp feature can either use a
ramp TIME or a ramp RATE. USE RATE is set to YES as the default (see SETPT function block details in Section3.2).
