HIMA F8628X处理器模块
将I/O扩展器板添加到标准机箱时（机箱选项2，带黑边条目连接器），订购连接器套件PN 16353-133以获得端子27-52。
•将I/O扩展器板添加到带有以太网连接器的标准机箱时（机箱选项4，灰色或绿色直接进入连接器），无需订购其他连接器。
•有关该套件的现场安装，请参阅提供的套件安装说明（15900-390）。
描述数量
I/O扩展器板-请勿将板从静电屏蔽中移除
装袋，直到安装完毕。
1.量程电阻器和参考接线盒，见下文1
PN16353-49量程电阻器和参考接线盒-该套件与上述I/O扩展器一起提供板套件和出厂的Moore 353，带扩展板选项1。配置概述
配置允许用户从可用列表中选择存储在控制器中的功能块，然后输入以实现特定的控制策略。虽然配置会影响整个站，控制器将相关的控制实现划分为循环。最多可以有99个循环
配置和25可以具有映射到网络通信2的操作员显示器
每个循环可以包含以下段落中列出的功能块。信号可以连接在
循环内以及循环之间的功能块。此外，还有几个车站功能块：
是固定的，可在STATION菜单中用于设置与STATION相关的值。
第3节全面描述了所有可用的功能块。有关调谐指南，请参阅第9.2节“自动调谐”
程序或请求AM-35数字控制器调谐。
注意
本用户手册包括MPU控制器板提供的功能
固件版本1.3和2.0至2.40。这些增强主要出现在
第2节和第3节。它们由短语“在版本1.3及更高版本中”或
文本中的“V1.3”或“V2.4”。
2.1车站功能块
永久性且可在车站菜单级访问的功能块：
FCO库………工厂配置选项库STATN………站参数安全性
时钟………实时时钟（需要固件V2.2或更高版本和RTC/CB板
以太网……以太网通信（需要固件2.4和以太网板）
2.2站硬件I/O块
配置期间可用的功能块取决于控制器中安装的硬件。这些块可以在循环中选择，但作为固定资源，一旦选择，将不再可用。左派
列显示每个块的最小和最大数量，右列显示
每个电路板。3
AIN1-4模拟输入MPU控制器板（3）、I/O扩展器板（1）
AINU1-2模拟输入，通用I/O扩展器板（2）
AOUT1-3模拟输出MPU控制器板（2）、I/O扩展器板（1）
DIN1-4数字输入MPU控制器板（3）、I/O扩展器板（1）
DINU1-2…………数字输入，通用…………I/O扩展器板（2）
DOUT1-2数字输出MPU控制器板（2）
ROUT1-2……继电器输出……I/O扩展器板（2）
2.3回路功能块
根据需要，在每个循环中，以下块可用，数量如下（如果没有，数量为1显示了数字）。某些块（例如A/M、偏置）只能在每个环路中使用一次。其他（如添加）
在循环中可重复使用，并可使用到指定的最大数量。每次可重用块
在循环中选择，将自动分配新的实例编号（即ADD01、ADD02）。每个循环
可以有一个操作员显示块（即ODC或ODS）。显示块定义循环的显示方式
When adding an I/O Expander board to a Standard Case (case Option 2, with black Side Entry
Connectors), order connector kit PN 16353-133 to obtain terminals 27-52.
• When adding an I/O Expander board to a Standard Case with Ethernet connector (case Option 4, with gray
or green Direct Entry Connectors), no additional connectors need be ordered.
• For field installation of this kit, see the supplied Kit Installation Instruction (15900-390).
DESCRIPTION QUANTITY
I/O Expander Board - Do not remove Board from static shielding
bag until it is to be installed.
1
Range Resistor and Reference Junction Kit, see below 1
PN16353-49 Range Resistor and Reference Junction Kit - This kit is supplied with the above I/O Expander
Board Kit and with a factory shipped Moore 353 with Expansion Board option 1. CONFIGURATION OVERVIEW
Configuration enables a user to select function blocks, stored in the controller, from an available list and enter
appropriate block parameters to implement a specific control strategy. Although configuration affects the entire
station, the controller partitions related control implementations into LOOPS. A maximum of 99 loops can be
configured and 25 can have operator displays that are mapped to network communications2
.
Each LOOP can contain the function blocks listed in the following paragraphs. Signals can be connected between
function blocks within the LOOP as well as between loops. Also, there are several STATION function blocks that
are fixed and available in the STATION menu for setting station related values.
Section 3 fully describes all available function blocks. For tuning guidelines refer to Section 9.2 Autotune
Procedure or request AM-35 Digital Controller Tuning.
NOTE
This User’s Manual includes the functionality provided by MPU Controller Board
firmware Versions 1.3 and 2.0 through 2.40. These enhancements appear mainly in
Sections 2 and 3. They are identified by the phrase “in version 1.3 and higher” or simply
“V1.3” or “V2.4” in text.
2.1 STATION FUNCTION BLOCKS
Function blocks that are permanent and accessible at the STATION menu level:
FCO LIB............Factory Configured Options Library
STATN...............Station Parameters
SECUR ..............Security
CLOCK .............real time CLOCK (requires firmware V2.2 or higher and RTC/CB board
ETHERNET......Ethernet Communications (requires firmware 2.4 and Ethernet board)
2.2 STATION HARDWARE I/O BLOCKS
Function blocks that are available during configuration depend on the hardware installed in the controller. These
blocks can be selected within a LOOP but as fixed resources, once selected, are no longer available. The left
column shows the minimum and maximum quantities of each block and the right column shows the quantity for
each circuit board.3
AIN1-4 .............Analog Input...................................MPU Controller Board (3), I/O Expander Board (1)
AINU1-2 ............Analog Input, Universal .................I/O Expander Board (2)
AOUT1-3 ...........Analog Output................................MPU Controller Board (2), I/O Expander Board (1)
DIN1-4 ..............Digital Input ...................................MPU Controller Board (3), I/O Expander Board (1)
DINU1-2 ............Digital Input, Universal..................I/O Expander Board (2)
DOUT1-2 ...........Digital Output.................................MPU Controller Board (2)
ROUT1-2 ...........Relay Output ..................................I/O Expander Board (2)
2.3 LOOP FUNCTION BLOCKS
The following blocks are available as needed within each loop in the quantities indicated (the quantity is one if no
number is shown). Some blocks (e.g. A/M, BIAS) can be used only once within each LOOP. Others (e.g. ADD)
are reusable within a LOOP and can be used up to the maximum number indicated. Each time a reusable block is
selected within a LOOP, a new instance number will automatically be assigned (i.e. ADD01, ADD02). Each LOOP
can have one operator display block (i.e. ODC or ODS). The display block defines how the loop will be displayed
