YOKOGAWA PW301模块,产品重量
VMIC产品上组装的一些组件可能对静电放电敏感，可能会对电路板造成损坏受到高能静电场的影响。未使用的电路板应存放在与装运时相同的保护箱中。当将板放置在工作台上进行配置等，建议将导电材料插入电路板下方，以提供导电性移走收到后，在运输集装箱内发现的任何预防措施应观察。所有物品应仔细打开包装，并彻底检查装运期间可能发生的损坏。
YOKOGAWA PW301模块应检查电路板对于损坏的组件、损坏的印刷电路板、热损坏和其他可见污染。因运输损坏引起的所有索赔应提交给承运人和发送给VMlC的完整报告以及咨询请求关于受损物品的处置。5.1.1开关和跳线位置参考图5-1，了解本节所述开关和跳线的位置部分5.2物理安装注意：通电时不要安装或拆卸电路板。断开设备电源，将电路板插入机箱，同时确保卡在支架中正确对齐和定向卡片导向器。将卡平稳地向前滑动到配对连接器上，直至牢固就坐的。5.3地址修饰符VMIVME-2511在工厂配置为响应短路监控I10通道通过安装跳线J9来启用电路板，可以更改此配置响应短的非特权I10访问。5.4跳线配置和详细的I10配置以下方框图显示了上可用的详细跳线选项VMIVME-2511。方框图参考P1/T#I.跳线定义表5-1除了定义一些未定义的跳线外，还详细解释了每个跳线的功能如图5-2所示*注1：这四个跳线仅用于缓冲I10选项。**注2：与支架配对的跳线相互排斥。如果其中一个跳线线对已安装，不得安装线对中的其他跳线，否则可能导致损坏
连接至VMIVME-2511或连接至VMIVME-2511的现场电子设备。
Some of the components assembled on VMIC's products may be
sensitive to electrostatic discharge and damage may occur on boards
that are subjected to a high energy electrostatic field. Unused boards
should be stored in the same protective boxes as shipped. When the
board is to be laid on a bench for configuring, etc., it is suggested that
conductive material be inserted under the board to provide a conductive
shunt.
Upon receipt, any precautions found in the shipping container should be
observed. All items should be carefully unpacked and thoroughly inspected for
damage that might have occurred during shipment. The board(s) should be checked
for broken components, damaged printed-circuit board(s), heat damage, and other
visible contamination. All claims arising from shipping damage should be filed with the
carrier and a complete report sent to VMlC together with a request for advice
concerning disposition of the damaged item(s).
5.1.1 SWITCH AND JUMPER LOCATIONS
Refer to Figure 5-1 for the locations of the switches and jumpers described in this
section.
5.2 PHYSICAL INSTALLATION
CAUTION: Do not install or remove boards while power is applied.
Deenergize the equipment and insert the board into an appropriate slot of the
chassis, while ensuring that the card is properly aligned and oriented in the supporting
card guides. Slide the card smoothly forward against the mating connector until firmly
seated.
5.3 ADDRESS MODIFIERS
The VMIVME-2511 is configured at the factory to respond to short supervisory I10
access. This configuration can be changed by installing jumper J9 to enable the board
to respond to short non-privileged I10 access.
5.4 JUMPER CONFIGURATION AND DETAILED I10 CONFIGURATION
The following block diagrams show the detailed jumpering options available on
the VMIVME-2511. The block diagrams reference P1/T #I. Jumper Definition Table 5-1
explains the function of each jumper in detail, in addition to defining some jumpers not
shown in Figure 5-2* NOTE 1 : These four jumpers are used only on the buffered I10 Option.
** NOTE 2: Jumpers paired with brackets are mutually exclusive. If one of the jumper
pairs is installed, the other jumper in the pair must not be installed or damage may result
to the VMIVME-2511 or to field electronics connected to the VMIVME-2511.
