BENTLY 125388-01H速度监测器
尝试通过以下方式将程序员连接到RX7i以太网将不成功。正常连接重试对话框不会显示。重新启动运行程序员的计算机将解决该行为。在一个系统中，如果硬件配置是从一个目标存储的，则不要使用多个目标目标和逻辑从另一个目标存储，通过闪存通电不起作用。观察到的行为是flash，机器版软件报告硬件配置和逻辑“不平等”。下载具有非常大的硬件配置或如果使用大量用户内存，则可能会遇到将配置写入闪存时出现“序列存储失败”错误。要解决此错误，可以执行以下任一操作或两个操作：有帮助：
BENTLY 125388-01H速度监测器1、在执行写入之前，执行明确的清除闪存。
2、增加机器版软件使用的操作超时在执行写入之前。这是通过扩展目标检查器窗口中的其他配置控制器，并调整请求超时。超时可能会需要增加到60000毫秒，具体取决于使用的内存量和闪存的状况在一些断电事件后，霍纳热电偶模块（HE697THM160）可能无法成功通电。失败后，%AI数据将无法正确更新，并将继续返回零值。此事件没有模块故障指示灯。用户应该再次通电以恢复正常功能。扩展机架中模块上的故障触点当扩展机架通电时，插槽故障触点将过早地表明扩展机架中的模块没有在完成通电之前出现故障。使用输入/输出点故障触点验证输入/输出的有效性。如果90-70系列远程输入/输出站和其中一个存在多个故障，则远程输入/输出站上的故障触点故障触点使用远程输入/输出站的模块参考将错误地指示远程输入/输出站。
BIT\u SEQ function block DIR参数BIT\u SEQ function block应要求用户流动布尔值逻辑转换为DIR参数，但目前没有。如果没有DIR参数如果存在，则默认情况下，BIT_SEQ将递增。
WinLoader可能会停止在运行Windows 2000并使用某些版本的Symantec防病毒保护，如果在advanced中使用，WinLoader将失败模式恢复需要循环计算机电源。
Infrequently, an attempt to connect a programmer to an RX7i via
Ethernet will be unsuccessful. The normal connection retry dialog will not
be displayed. Rebooting the computer that is running the programmer
will resolve the behavior.
Don’t use multiple targets In a system in which the hardware configuration is stored from one
target and logic is stored from a different target, powering-up from flash
will not work. The observed behavior is that, following a power up from
flash, Machine Edition software reports hardware configuration and logic
"not equal".
Sequence store failure When downloading projects with very large hardware configuration or
which use large amounts of user memory, it is possible to encounter a
“Sequence Store Failure” error when writing the configuration to flash.
To work around this error, either or both of the following actions may be
helpful:
1. Perform an explicit clear of flash prior to performing the write.
2. Increase the operation timeout used by Machine Edition software
prior to performing the write. This is done by expanding the
Additional Configuration in the Inspector window for the target
controller, and adjusting the Request Timeout. The timeout may
need to be increased to as much as 60000 msec, depending on
the amount of memory used and the condition of the flash memoryfter some power loss events, the Horner Thermocouple module
(HE697THM160) may fail to power up successfully. After failure, the %AI
data will not be updated correctly and will continue to return zero values.
There are no module fault indicators for this event. The user should
power cycle again to restore normal function.
Fault contacts on modules in expansion rack When an expansion rack powers up, the slot fault contacts will
prematurely indicate that the modules in the expansion rack are not
faulted before they complete their power up. Use I/O point fault contacts
to verify validity of the I/O.
Fault contacts on Remote I/O Station If multiple faults exist in a Series 90-70 Remote I/O Station and one of
them is corrected, a FAULT contact that uses the Remote I/O Station’s
module reference will incorrectly indicate that no faults exist at the
Remote I/O Station.
BIT_SEQ function block DIR parameter The BIT_SEQ Function Block should require the user to flow BOOLEAN
logic into the DIR parameter, but currently does not. If no DIR parameter
is present, the BIT_SEQ will increment by default.
WinLoader may stop operating On computers running Windows 2000 and using some versions of
Symantec Antivirus protection, WinLoader will fail if used in advanced
mode. Recovery requires cycling the computer's power.
