VIBRO 200-566-000-012卡件使用数据
MVME761过渡模块安装本节适用于MVME761兼容型号的MVME2603/2604 VME模块。安装MVME2603/2604后,参考图1-22,按照以下步骤安装MVME761
过渡模块:1、将静电带系在手腕上。连接ESD的另一端
将皮带系在底盘上作为接地。静电放电带必须固定在在整个过程中,您的手腕和地面。
VIBRO 200-566-000-012卡件使用数据2、执行操作系统关机。接通交流或直流电源断开并从系统中卸下交流电源线或直流电源线。根据需要卸下机箱或系统盖,以便访问VME模块MVME2600、MVME761兼容型号将在以下情况下损坏:错误地连接到MVME712系列板,而不是纠正MVME761过渡模块。注:在MVME761兼容型号中,某些信号是通过P2多路复用以增加输入/输出容量。提到P2信号多路复用,详见第3-15页。在通电的情况下插入或拆卸模块可能会导致损坏至模块组件。
在这种情况下,存在可能导致死亡的危险电压设备搬运、测试和调整时要格外小心。
机箱的前部或后部。(您可能需要将其他模块移入机箱为MVME761的布线留出空间。)图1-22。MVME761/MVME2603/2604电缆连接5.将配备MVME761的64芯电缆从P2适配器板上的J3到过渡模块上的P2。确保用连接器针脚1.6定位电缆针脚1。用提供的螺钉将MVME761固定在机箱中,与横向安装轨道接触良好,以将射频发射。
注:可以通过多种方式配置布线,以适应各种设备和系统配置。图1-22显示了一种可能的配置。有关更多详细信息有关安装P2适配器板和的信息MVME761过渡模块,请参阅用户手册(列出附录D,相关文件)。
MVME761 Transition Module Installation
This section applies to MVME761-compatible models of the
MVME2603/2604 VME module. With the MVME2603/2604 installed,
refer to Figure 1-22 and proceed as follows to install an MVME761
transition module:
1. Attach an ESD strap to your wrist. Attach the other end of the ESD
strap to the chassis as a ground. The ESD strap must be secured to
your wrist and to ground throughout the procedure.
2. Perform an operating system shutdown. Turn the AC or DC power
off and remove the AC cord or DC power lines from the system.
Remove chassis or system cover(s) as necessary for access to the
VME modulesThe MVME2600, MVME761-compatible models will be damaged if
mistakenly connected to the MVME712 family of boards instead of the
correct MVME761 transition modules.
Note In MVME761-compatible models, certain signals are
multiplexed through P2 for additional I/O capacity. Refer to
P2 Signal Multiplexing on page 3-15 for details.Inserting or removing modules with power applied may result in damage
to module components.
!
Warning
Dangerous voltages, capable of causing death, are present in this
equipment. Use extreme caution when handling, testing, and adjusting.
3. Remove the filler panel(s) from the appropriate card slot(s) at the
front or rear of the chassis. (You may need to shift other modules in
the chassis to allow space for the cabling to the MVME761.)Figure 1-22. MVME761/MVME2603/2604 Cable Connections
5. Route the 64-conductor cable furnished with the MVME761 from
J3 on the P2 adapter board to P2 on the transition module. Be sure
to orient cable pin 1 with connector pin 1.6. Secure the MVME761 in the chassis with the screws provided,
making good contact with the transverse mounting rails to minimize
RF emissions.
Note The cabling can be configured in a number of ways to
accommodate various device and system configurations.
Figure 1-22 shows one possible configuration. For more detailed
information on installing the P2 adapter board and the
MVME761 transition module, refer to the user’s manual (listed
in Appendix D, Related Documentation).