IS220PVIBH1AL电气模块,IS220PVIBH1AL使用数量
完整的设置由许多主菜单和子菜单组成。下表显示了逐步完成整个设置时，按外观顺序排列主菜单。桌子也概述了您可以在以下每个主菜单中进行的选择和参数设置。完整的设置顺序在第3.12节中进行了描述。本节提供了一个分步说明，详细介绍了所有可用的带有相关参数、数据和设置的设置菜单。使用上下键从列表中选择语言[ZZ]、单位[ZZZ]和小数位数[Z]。
IS220PVIBH1AL电气模块菜单SetWebWidth仅在选择单位N/m、kN/m、kg/m或pli时可用。设置语言以下语言可用：?英语、德语、意大利语、法语、葡萄牙语和日语3.12.1.2机组可以设置以下单位：?N（牛顿）?kN（千牛顿）?kg（千克如果所选单位为N/m、kN/m、kg/m或pli，则需要设置腹板宽度。默认腹板宽度为2m（78740英寸）。3.12.1.3设置腹板宽度菜单SetWebWidth仅在所选单位为N/m、kN/m、kg/m或物价指数。默认腹板宽度为2m（78740英寸）。格式为XX。如果宽度以米和XXXX输入，则为XXX。XX如果输入宽度英寸最大腹板宽度为50m（1968,5英寸）3.12.1.4集合小数可以在此菜单中设置显示的小数位数。可以设置小数位数根据称重传感器标称负载和表示单元，将其设置为0-5之间的数字。第4.6节进一步解释了集合小数函数。在菜单系统定义中，必须设置以下内容：称重传感器梳（称重传感器组合）–一卷（称重传感器A和B）–两个辊（辊1连接到A和B；辊2连接到C和D）–分段滚动?收益计划（包裹收益计划）。可用于一卷、两卷（仅第1卷）和分段滚动。
The complete setup is built up by a number of main and sub menus. The table below shows the
main menus in order of appearance when stepping through the complete setup. The table also
gives an overview of the selections and parameter settings you can do below in each main menu.
The complete setup sequence is described in Section 3.12This section provides a step-by-step description with detailed information about all available
setup menus with related parameters, data and settings.Use up and down keys to select language [ZZ], unit [ZZZZ] and number of decimals [Z] from list.
The menu SetWebWidth will only be available when unit N/m, kN/m, kg/m or pli is selected.Set Language
The following languages are available:
? English, German, Italian, French, Portuguese and Japanese
3.12.1.2 Set Unit
The following units can be set:
? N (Newton)
? kN (kiloNewton)
? kg (kilogramIf the selected unit is N/m, kN/m, kg/m or pli, the Web Width needs to be set.
Default Web Width is 2m (78,740 inch).
3.12.1.3 Set Web Width
The menu SetWebWidth will only be available when the selected unit is N/m, kN/m, kg/m or
pli.
Default Web Width is 2m (78,740 inch).
The format is XX.XXX if the width is entered in meter and XXXX.XX if the width is entered in
inch. Maximum Web Width is 50m (1968,5 inch)
3.12.1.4 Set Decimals
The number of displayed decimals can be set in this menu. The number of decimals may be set
to a number between 0 - 5 depending on the load cell nominal load and presentation unit.
Set decimals function is further explained in Section 4.6.In menu SystemDefinition the following must be set:
? LoadCellComb (load cell combination)
