TSXPBY10模块,TSXPBY10产品颜色
在总线配置中配置Genius NIU时Genius总线控制器，为%I、%Q、%AI指定的数据长度%AQ数据必须与NIU的硬件配置相匹配。如果总线控制器和NIU的输入/输出数据长度不匹配，NIU不会加入公交车，也不会报告系统由不匹配引起的配置不匹配故障。）正确的输入/输出数据长度可以通过检查Genius NIU的硬件配置。程序此处描述的是机器版逻辑开发人员-PLC编程软件。
a、 如果Genius NIU硬件配置可用：1） 打开包含Genius NIU目标和选择NIU目标。
TSXPBY10模块2） 在NIU目标下，右键单击硬件配置并选择“硬件参考视图”。
3） 对于每个输入/输出数据选项卡（%I等），使用最大的地址在“结束”列中，作为该输入/输出数据的数据大小类型如果没有数据类型的条目，则数据该类型的长度为零。
b、 如果Genius NIU硬件配置不可用：
1） 连接运行编程的Windows PC使用VersaMax NIU序列将软件发送到Genius NIU电缆，IC200CBL002。
2） 为GE Fanuc PLC创建一个新项目。在新的项目，创造一个新的天才牛的目标。
3） 将硬件配置从Genius NIU上传到目标。
4） 在NIU目标下，右键单击硬件配置并选择“硬件参考视图”。
5） 对于每个输入/输出数据选项卡（%I等），使用“End”列作为该输入/输出数据类型的数据大小。如果数据类型没有条目，数据长度为该类型为零。
9.如果GNIU试图使用具有以下特征的配置联机：输入/输出类型和长度与控制器，GNIU的系统配置不匹配故障将出现在控制器的PLC故障表中：该故障由控制器本身。GNIU中存在的其他故障不会直到纠正输入/输出类型和长度的不匹配。10、当主机控制器处于停止模式且GNIU处于配置为双总线操作，对GNIU进行电源循环立即将总线从总线A切换到总线B。GNIU即使主机控制器进入运行模式。
When configuring a Genius NIU in the bus configuration for a
Genius Bus Controller, the data lengths specified for %I, %Q, %AI
and %AQ data must match the hardware configuration of the NIU.
If the I/O data lengths of the Bus Controller and NIU do not match,
the NIU will not join the bus and will not report the System
configuration mismatch fault caused by the mismatch.)
The correct I/O data lengths can be determined by examining the
hardware configuration for the Genius NIU. The procedure
described here is for Machine Edition Logic Developer – PLC
programming software.
a. If the Genius NIU hardware configuration is available:
1) Open the project that includes the Genius NIU target and
select the NIU target.
2) Under the NIU target, right-click on Hardware
Configuration and select “Hardware Reference View”.
3) For each I/O data tab (%I, etc.), use the largest address
in the “End” column as the data size for that I/O data
type. If there are no entries for a data type, the data
length for that type is zero.
b. If the Genius NIU hardware configuration is NOT available:
1) Connect the Windows PC running the programming
software to the Genius NIU using a VersaMax NIU serial
cable, IC200CBL002.
2) Create a new project for a GE Fanuc PLC. Within the
new project, create a new Genius NIU target.
3) Upload the hardware configuration from the Genius NIU to
the target.
4) Under the NIU target, right-click on Hardware
Configuration and select “Hardware Reference View”.
5) For each I/O data tab (%I, etc.), use the largest address in
the “End” column as the data size for that I/O data type. If
there are no entries for a data type, the data length for
that type is zero.
9. If the GNIU attempts to come online with a configuration that has
I/O types and lengths that do not match those expected by the
controller, a System Configuration Mismatch fault for the GNIU will
appear in the controller's PLC fault table: This fault is generated by
the controller itself. Additional faults present in the GNIU do not
appear until the mismatch in I/O types and lengths is corrected.
10. When the host controller is in STOP mode and the GNIU is
configured for dual bus operation, a power cycle to the GNIU
switches the bus from BUS A to BUS B immediately. The GNIU
does not switch back from BUS B to BUS A even if the host
controller goes to RUN mode.
