IS220YDIAS1A燃机电气,IS220YDIAS1A实验数据
与任何其他模块的使用相冲突。离散输入(%I)和输出(%Q)寄存器用于分别监视状态和发起呼叫。3.7.1拨号%R的使用和配置拨号%R是配置时使用HHP和第二和第三字节的最后一个参数PLC软件。使用HHP,拨号%R参数以十进制形式输入。使用PLC
在配置软件中,拨号%R设置必须分为高(字节3)和低(字节2)字节值,然后转换为适当的二进制格式。值转换为二进制后形式,它被放置在配置的字节2中。
IS220YDIAS1A燃机电气拨号%R参数使用的寄存器数量取决于用户的号码长度希望拨打。每个寄存器最多包含两个字符。例如,如果用户是调用7位数字,然后使用4个连续寄存器。配置的8%I寄存器提供调制解调器的状态。在配置的8%Q寄存器中,只有第一个已使用。%Q1用于启动呼叫。高转换(1)启动呼叫。低转换(0)清除状态寄存器。下页包含状态和控制寄存器及其使用。另请参阅拨号%R示例部分以获取帮助。与任何其他模块的使用相冲突。离散输入(%I)和输出(%Q)寄存器用于分别监视状态和发起呼叫。3.7.1拨号%R的使用和配置拨号%R是配置时使用HHP和第二和第三字节的最后一个参数PLC软件。使用HHP,拨号%R参数以十进制形式输入。使用PLC
在配置软件中,拨号%R设置必须分为高(字节3)和低(字节2)字节值,然后转换为适当的二进制格式。值转换为二进制后形式,它被放置在配置的字节2中。
拨号%R参数使用的寄存器数量取决于用户的号码长度希望拨打。每个寄存器最多包含两个字符。例如,如果用户是调用7位数字,然后使用4个连续寄存器。配置的8%I寄存器提供调制解调器的状态。在配置的8%Q寄存器中,只有第一个已使用。%Q1用于启动呼叫。高转换(1)启动呼叫。低转换(0)清除
状态寄存器。下页包含状态和控制寄存器及其使用。另请参阅拨号%R示例部分以获取帮助。
conflict with the use of any other module. Discrete input (%I) and output (%Q) registers are used to
monitor status and initiate calls, respectively.
3.7.1 Use and Configuration of Dial %R
The Dial %R is the last parameter using the HHP and the second and third Byte when configuring with
the PLC Software. Using the HHP, the Dial %R parameter is entered in decimal form. Using the PLC
Configuration Software, the Dial %R setting must be divided into a high (Byte 3) and a low (Byte 2) Byte
value and then converted to the appropriate binary format. Once the value has been converted to binary
form, it is placed in Byte 2 of the configuration.
The number of registers used by the Dial %R parameter depends upon the length of the number the user
wishes to dial. Each register contains a maximum of up to two characters. For example, if the user is
calling a 7-digit number, then 4 consecutive registers are used.
The 8 %I registers configured give the status of the modem. Of 8 %Q registers configured, only the first
is used. %Q1 is used to initiate the call. A high transition (1) initiates the call. A low transition (0) clears
the status register. The following page contains a detailed list of the status and control registers and their
uses. Also see the Dial %R Example section for help.